manualshive.com logo in svg

SMC Networks 8728L2 - annexe 1, Management Manual

The SMC Networks 8728L2 - annexe 1 is a power-packed managed switch designed for efficient network management. With its comprehensive Management Manual, users can easily navigate through advanced features and configurations. Download this essential manual for free from manualshive.com to maximize the potential of your SMC Networks 8728L2 - annexe 1.

Share
Download
background image

C

OMMAND

 L

INE

 I

NTERFACE

4-116

uses 1 bits to indicate “match” and 0 bits to indicate “ignore.” The 
bitmask is bitwise ANDed with the specified source IP address, and 
then compared with the address for each IP packet entering the port(s) 
to which this ACL has been assigned.

Example 

This example configures one permit rule for the specific address 10.1.1.21 
and another rule for the address range 168.92.16.x – 168.92.31.x using a 
bitmask.

Related Commands

access-list ip (4-114)

permit

,

 deny 

(Extended ACL)

 

This command adds a rule to an Extended IP ACL. The rule sets a 
filter condition for packets with specific source or destination IP 
addresses, protocol types, source or destination protocol ports, or TCP 
control codes. Use the 

no

 form to remove a rule.

Syntax

[

no

] {

permit

 | 

deny

} [

protocol

-

number | 

udp

] 

{

any

 | 

source address-bitmask | 

host

 

source

} 

{

any

 | 

destination address-bitmask | 

host 

destination

}

[

source-port

 

sport 

[

end

]] [

destination-port

 

dport 

[

end

]]

[

no

] {

permit

 | 

deny

} 

tcp

 

{

any

 | 

source address-bitmask | 

host

 

source

} 

{

any

 | 

destination address-bitmask | 

host

 

destination

}

[

source-port

 

sport 

[

end

]] [

destination-port

 

dport 

[

end

]]

•

protocol-number

 – A specific protocol number. (Range: 0-255)

•

source

 – Source IP address.

•

destination

 – Destination IP address.

•

address-bitmask

 – Decimal number representing the address bits to 

match.

•

host 

– Keyword followed by a specific IP address.

Console(config-std-acl)#permit host 10.1.1.21
Console(config-std-acl)#permit 168.92.16.0 255.255.240.0
Console(config-std-acl)#

Summary of Contents for 8728L2 - annexe 1



































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 8728L2 - annexe 1

OEZ PS-LT Instructions For Use preview
PS-LT
Brand: OEZ Pages: 5
AVE 8PSWT Specification preview
8PSWT
Brand: AVE Pages: 2
hager TS 204 User Instruction preview
TS 204
Brand: hager Pages: 2
UniFi USW-Flex-Mini Quick Start Manual preview
USW-Flex-Mini
Brand: UniFi Pages: 8
VeEX AT1701 User Manual preview
AT1701
Brand: VeEX Pages: 22
Eaton AGswitch Instructions Manual preview
AGswitch
Brand: Eaton Pages: 36
LEGRAND HKRL20 Installation Manual preview
HKRL20
Brand: LEGRAND Pages: 30
Radial Engineering Cherry Picker User Manual preview
Cherry Picker
Brand: Radial Engineering Pages: 8
LEGRAND 672 34 Quick Start Manual preview
672 34
Brand: LEGRAND Pages: 4
Black Box LGB408A-R2 Manual preview
LGB408A-R2
Brand: Black Box Pages: 20
NETGEAR GS316P Installation Manual preview
GS316P
Brand: NETGEAR Pages: 8
ICCN WX7020-1210G Web User Manual preview
WX7020-1210G
Brand: ICCN Pages: 48
Cypress SE-DVI-8-LC Operation Manual preview
SE-DVI-8-LC
Brand: Cypress Pages: 4
Generac Power Systems TRANSFER SWITCH Warranty Information Booklet preview
TRANSFER SWITCH
Brand: Generac Power Systems Pages: 1
Vivanco SBX 95 SE - AV Control 4 Instructions Manual preview
SBX 95 SE - AV Control 4
Brand: Vivanco Pages: 16
Linksys SRW224 - 10/100 - Gigabit Switch Specifications preview
SRW224 - 10/100 - Gigabit Switch
Brand: Linksys Pages: 2
ANTIFERENCE Clear Switch CF-POE8 User Manual preview
Clear Switch CF-POE8
Brand: ANTIFERENCE Pages: 7
Fore Systems forerunner series Configuration Manual preview
forerunner series
Brand: Fore Systems Pages: 352

Brands by name

Popular brands

Load more brands