Sifos Technologies PhyView PVA-3000 Reference Manual Download Page 105

Page: 105 / 134

PVA-3000 Reference Manual

December 2, 2019

Sifos Technologies

Page
105

4.18.6.

Example 6: Establish and Verify Packet Forwarding in a Switch

Test Ports 1,1 and 1,2 need to be connected to a DUT that supports packet forwarding.  Verify that both ports 1,1 and
1,2 are linked before performing the following tasks.

Hint:  Pre-configure test ports for

AUTO Address

All Ports

– this will assure that packets originated in test port 1,1

are addressed to test port 1,2 and visa versa. Also, be sure to prime any switch bridging logic prior to forwarding
packets.

# Example 6 script
# Using PVA-3102 in slot,port 1,1 for Tx, 1,2 for Rx
# Configure MAC Addresses for transmission 1,1 to 1,2 and back

set TxPort 1,1
set RxPort 1,2

pva_pkt_addr

$TxPort auto match store

# Configure both Test Ports for auto speed, duplex, polarity.

pva_speed

$TxPort auto duplex auto arm

pva_polarity

$TxPort auto arm

pva_speed

$RxPort auto duplex auto arm

pva_polarity

$RxPort auto arm

# Force a re-link, to establish the desired line conditions.

pva_relink

$TxPort

pva_relink

$RxPort

# Verify that the links are up.

pva_link_wait

$TxPort

pva_link_wait

$RxPort

# Transmit Traffic on both ports to prime any switch bridging

pva_tx_pkt

$TxPort size 60 rate line count 0

pva_tx_pkt

$RxPort size 60 rate line count 0

after 30000

pva_tx_pkt

$TxPort stop

pva_tx_pkt

$RxPort stop

# Start the Received Packet Counter on the RxPort.

set rslt [

pva_rx_pkt

$RxPort start]

# Transmit 512k packets with the TxPort

set rslt [

pva_tx_pkt

$TxPort size 60 rate line count 512K

start]

# Check for Transmit completed

while {[lindex [

pva_tx_pkt

$TxPort stat] 3] != "IDLE"} { }

# Read the Received Packet Counter.

set rslt [

pva_rx_pkt

$RxPort stat]

# Stop the Received Packet Counter.

pva_rx_pkt

$RxPort stop

Summary of Contents for PhyView PVA-3000







































































































































Search results

Summary of Contents for PhyView PVA-3000

Reviews:

Related manuals for PhyView PVA-3000

Brands by name

Popular brands

Sifos Technologies PhyView PVA-3000, Reference Manual

Search results

Summary of Contents for PhyView PVA-3000

Reviews:

Related manuals for PhyView PVA-3000

Brands by name

Popular brands