Sifos Technologies PhyView PVA-3000 Reference Manual Download Page 47 | Manualshive

Page: 47 / 134

background image

PVA-3000 Reference Manual

December 2, 2019

Sifos Technologies

Page
47

3.8.1.

Link Config Menu-Wide Controls

The Link Config menu can be used to force a re-link at any time simply by pressing the

RE-LINK

button. This is the

logical equivalent of disconnecting, then re-connecting a patch cable to the port-under-test. As described below, this
control will frequently be used whenever re-configuring link parameters. By default, the re-link only occurs on the
current test port, however, when

Re-link All Ports

is checked, the

RE-LINK

control will impose new link-ups on all

PVA test ports in the currently connected PVA instrument.

The

Read Settings

button can be used at any time to update current test port link and TEST PHY settings to the Link

Config tab menu. Generally, this operation is not frequently necessary because each time a new test port is selected in
the Slot-Port helper menu or each time the

Link Config

tab menu is selected, all displayed settings will update

automatically to match actual resource setting in the test port. The

Read Settings

button will also clear out any

pending configuration changes and assure synchronization of the Link Config tab menu to associated test port
resources.

The Link Config menu also offers the

Reset Test PHY

control to reset the TEST PHY. When the TEST PHY is reset,

from PVA Interactive, many of the internal features of the TEST PHY will be returned to the initial power-up state.
For example,

Transmit Level

,

Transmit Slew

, and

Receiver Sensitivity

are returned to TEST PHY

Automatic

control regardless of previous configuration. Any activated test signals are shut off and a new link-up is initialized.
Previously configured link configurations including

Link Speed

,

Link Duplex

,

Link Polarity

, and

Gigabit Config

will be retained

however so that the link-up that occurs following the reset will adhere to previous configuration

settings.

As with the

RE-LINK

control, the

Reset Test PHY

operation can be broadcast to all PhyView Analyzer test ports in

the currently connected instrument by selecting the

Reset All Ports

checkbox prior to pressing the

Reset Test PHY

button.

3.8.2.

Link and Gigabit Configuration Sub-Menus

Each PhyView Analyzer test port offers a wide range of link configurations that can be used primarily to force a
device-under-test (DUT) into a desired operating mode so that particular physical layer assessments can be performed.
Since 10/100/1000BaseT link configuration is determined during initial link-up, the process of modifying a link
configuration always involves 2 steps:

1.

Define the configuration

4.

Re-link to the DUT (i.e.

RE-LINK

button)

The link configurations that can be controlled from PVA Interactive are:



Link Speed (using Auto-Negotiation)



Link Duplex (using Auto-Negotiation)



Link (connection) Polarity (MDI, MDI-X, or Auto MDI/MDI-X)



Gigabit Timing Mode (using Auto-Negotiation)

The Link Config sub-menu offers five choices for

Link Speed

(or rate):

Automatic

: Allow auto-negotiation to resolve link speed

1000BaseT

: Force a 1000BaseT link-up

100BaseTx

: Force a 100BaseTx link-up

10BaseT

: Force a 10BaseT link-up

10+100BaseT

: Allow auto-negotiation to choose between 100BaseTx and 10BaseT link-up

Whenever a particular Link Speed is selected, the

Arm Configuration

button will

annunciate

red

indicating that the new configuration will not be

defined

until that button is

pressed (

see Figure 3.15

). Pressing

Arm Configuration

will then define the new

configuration that will take affect on the next link-up. Once defined (or “armed”), the new
link configuration will take effect when the

RE-LINK

button is pressed. It would also take

effect if the patch cable were re-connected.

Link Duplex

can be configured for

Automatic

,

Full Duplex

, and

Half Duplex

following the same two-step process of

Arm Configuration

and

RE-LINK

. Generally, the duplex configuration of a link is not significant in the outcome of

physical layer measurements and receiver testing meaning that the

Automatic

setting will normally work fine for most

operations.

Figure 3.15

Link Config

Sub-Menu

«
...
45
46
47
48
49
...
»

Summary of Contents for PhyView PVA-3000







































































































































Reviews:

No comments

Related manuals for PhyView PVA-3000

DigitalFlow XMT868i

Brand: Panametrics Pages: 74

Brand: Eaton Pages: 53

Brand: Oceanic Pages: 75

ORBISPHERE 3624

Brand: Hach Ultra Pages: 12

Brand: OHAUS Pages: 52

Brand: jenway Pages: 18

NANOCOLOR Advance

Brand: Macherey-Nagel Pages: 45

Brand: Pangea Pages: 2

Brand: ISKRAEMECO Pages: 12

RAVTD1760WS Series

Brand: Ravaglioli Pages: 24

Brand: Tire-Safeguard Pages: 6

PASPORT PS-2174

Brand: PASCO Pages: 4

Brand: Unipro Pages: 2

Brand: IFM Pages: 17

Brand: Chauvin Arnoux Pages: 10

Brand: Hanna Instruments Pages: 2

WATERPROOF PHTESTR 1 PH TESTER

Brand: EUTECH INSTRUMENTS Pages: 3

AirScout Gigacheck

Brand: Greenlee Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands