Sifos Technologies PhyView PVA-3000 Reference Manual Download Page 23 | Manualshive

Page: 23 / 134

background image

PVA-3000 Reference Manual

December 2, 2019

Sifos Technologies

Page
23

2.

PhyView Analyzer Overview

Each test port in a PhyView Analyzer is an autonomous test instrument for assessing 10/100/1000BaseT Ethernet
physical layer performance characteristics. This section will review all of the testing resources within each test port
and their respective capabilities and applications.

2.1.

Test Port Interfaces and Configurations

Each PhyView Analyzer (PVA) test port includes 2 external RJ-45 socket interfaces, a

TEST

interface and a

THRU

interface. The

TEST

interface is always connected to the device-under-test, usually an Ethernet 10/100/1000BaseT

port. The

THRU

interface may optionally be used with external test equipment such as an Ethernet packet analyzer.

10/100/1000BaseT signaling that passes through the

TEST

interface will always

experience a 2.6dB power loss as it traverses a passive RF

4-Pair Coupler

(

see

Figure 2.1

). This loss is frequency flat through 100MHz and is implemented with

100



matching impedance so as not to disturb any 100



terminations. It is

uniformly applied to each of the four LAN pairs.

The

PVA Switch

in

Figure 2.1

then determines whether the

TEST

interface will be

terminated locally inside the test port or whether it will be transferred to the

THRU

interface so that it can be connected to external instrumentation. The PVA Switch
is an electro-mechanical relay with DC to 1GHz frequency response. When the

TEST

interface is connected to the

THRU

interface, all of the PVA test port

measurement capabilities become unavailable while certain impairments resources
remain fully available as “in-line” resources to external test equipment (

see Figure

2.2

).

Figure 2.2

PVA THRU Interface

Figure 2.1

PhyView Analyzer Test Port Architecture

«
...
21
22
23
24
25
...
»

Summary of Contents for PhyView PVA-3000







































































































































Reviews:

No comments

Related manuals for PhyView PVA-3000

Brand: Yamaha Pages: 8

Brand: Oldham Pages: 43

Brand: Eaton Pages: 53

Brand: Oceanic Pages: 75

Portable Grand DGX-670

Brand: Yamaha Pages: 93

Portatone PSR-410

Brand: Yamaha Pages: 65

Brand: LumaSense Pages: 23

Brand: RHS Pages: 8

Brand: Ramsey Electronics Pages: 40

Brand: Omega Pages: 20

Brand: Major tech Pages: 20

CR-2010 PRO Series

Brand: G-Tek Pages: 48

Brand: iSTEK Pages: 15

Roast Alert/3 ET-8C

Brand: Redi-Chek Pages: 3

AquaShock 850046K

Brand: Sper scientific Pages: 28

Brand: SCINTREX Pages: 265

BIP LD2-T017-01-EP-S4 Series

Brand: Balluff Pages: 16

Brand: janitza Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands