Sifos Technologies PhyView PVA-3000 Reference Manual Download | Manualshive

Page: 77 / 134

background image

PVA-3000 Reference Manual

December 2, 2019

Sifos Technologies

Page
77

4.5.

Test Port Trigger Generation

The Test Port Event Trigger is used to enable synchronization of measurements across multiple test ports and multiple
instruments. This broadcast trigger capability was described earlier in Section 2.2.5. It is only available in PVA-3000,
PVA-3002, PSA-3000, and PSA-1200 instruments meaning it is not available in PSL-3000 and PSA-1200-PL
platforms.

Command

Port

Command Parameters

Query

Returned
Parameters

trigout

<

port

>

Produces an immediate broadcast Event Trigger.

4.6.

Test Port PHY Link Configuration

Test PHY Link Configuration commands and queries govern configurations of a 10/100/1000BaseT connection
between the Test PHY and a potential link partner. Configurations were addressed earlier in Section 2.2.1. Some of
these commands accept the broadcast configuration where

port

= 99,99.

Command

Port

Command Parameters

Query

Returned
Parameters

pva_reset

<

port

>

<

restore

>

Resets the Test PHY to known “power-on” state with auto-
negotiation fully enabled. Default is to reset all aspects of
Test PHY including Auto-Negotiation defaults and front-end
configurations. Accepts broadcast

port

= 99,99.

restore

: Retain present link rate (speed), duplex mode,

polarity, and gigabit timing mode following the reset.

pva_relink

<

port

>

Causes an immediate re-link to occur using any Auto-
Negotiation configurations previously specified and returns
link status. Accepts broadcast

port

= 99,99.

pva_speed

<

port

>

auto

|

1000

|

100

|

10

|

10+100

<

duplex auto

|

full

|

half

>

<

arm

>

LINKED |

UNLINKED |

ARMED

Configures Test PHY to advertise selected speed and link
duplex mode through either an immediate re-link (default)
or through a re-link to occur later. Note: Use command

pva_relink

to initiate the link change if “

arm

” is specified.

Use

pva_link_mon

to query link status. Returns

LINKED

if re-link is successful, returns

UNLINKED

if re-link fails,

and returns

ARMED

if ‘arm’ specified. Accepts broadcast

port

= 99,99 only in combination with

arm

argument.

auto

Configure speed to whatever rate is auto-negotiated

with link partner. Test PHY supports 10/100/1000BaseT.
(

wake-up default

)

1000

Configure Test PHY to advertise only 1000BaseT

available

100

Configure Test PHY to advertise only 100BaseTX

available

10

Configure Test PHY to advertise only 10BaseT available

10+100

Configure Test PHY to advertise both 100BaseTX

and 10BaseT available

duplex auto

Allow links to auto-negotiate for duplex mode

duplex full

Force link to full duplex only

duplex half

Force link to full duplex only

arm

Configure link speed and duplex mode but suppress

any re-link (auto-negotiation) until a later re-link operation
takes place. Enables use with port ‘99,99’.

?

AUTO

|

1000 | 100 | 10 |
10+100

+

AUTO

| FULL |

HALF | VARIOUS

«
...
75
76
77
78
79
...
»

Summary of Contents for PhyView PVA-3000







































































































































Reviews:

No comments

Related manuals for PhyView PVA-3000

Brand: TANDBERG Pages: 53

Brand: VELOCICALC Pages: 6

Brand: Panametrics Pages: 68

Brand: M-system Pages: 18

Brand: T&D Pages: 2

Brand: T&D Pages: 2

Clavinova CVP-601

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 28

Brand: Teledyne Analytical Instruments Pages: 107

WALLACE & TIERNAN P7 ADVANCED

Brand: Evoqua Pages: 98

Brand: Elcontrol Pages: 7

FrameSaver SLV Series

Brand: Paradyne Pages: 39

Brand: Opus Technologies Pages: 24

Brand: Aalborg Pages: 56

Brand: Keysight Pages: 42

Brand: Orange Research Pages: 2

Brand: Sub Aqua Pages: 4

Brand: Avtech Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands