Sifos Technologies PhyView PVA-3000 Reference Manual Download Page 92 | Manualshive

Page: 92 / 134

background image

PVA-3000 Reference Manual

December 2, 2019

Sifos Technologies

Page
92

Command

Slot

Command Parameters

Returned
Parameters

mp_xtalk

<

port1 port2

..

portN

>

pairs

pairGrp

<

avg

nAvgs

>

{

slot

,

port_1

+

(

READY

+

Xtalk(dB))

|

UNLINKED

…

slot

,

port_N

+

(

READY

+

Xtalk(dB))

|

UNLINKED

}

Perform 1000BaseT Bulk Crosstalk measurements and produce meter
results for multiple test ports on a selected pair group given 1000BaseT
link-ups. Measurements will run simultaneously on all selected Test
Ports.

port1 port2

..

portN

Ports to test.

pairs

pairGrp

Specifies LAN PAIR GROUP to measure. Range is 12,

13, 14, 23, 24, or 34. where 1 is TIA blue pair, 2 is TIA orange pair, 3
is TIA green pair, and 4 is the TIA brown pair.

avg

nAvgs

Specifies non-default number of averages to use in

measurement. Range is 1 to 64. Default is 8.

4.15. PowerShell System & Chassis Commands

System commands are utilized to control and configure at the PowerSync Analyzer chassis level. The

pva

command

described in Section 4.5 above will define the chassis on which each of these commands will operate.

Command

Command Parameters

Returned
Parameters

pva_config

<

-

d

|

-

s

>

{Port + Type +
Version}

Inventories and reports status of available system resources (blades,
ports, firmware version). Inventory is performed upon currently selected
PVA instrument (see “pva” command). Default output is TCL List of
inventory.

-d

Causes inventory to be displayed in tabular form.

-s

Returns a list of populated slots

trig_port

<

in

|

out

>

{INPUT |
OUTPUT}

Configures the TRIG port on the PSA1200 chassis controller to output or
input external trigger signals. Default (wake-up) mode is output.

in

: Trig port on PSA1200 Controller becomes an input to

the “external

trigger” bus.

out

: Trig port on the PSA1200 Controller becomes and output of the

“external trigger” signal.

psa_setipaddress

ipaddress

<

m

ask

mask

> <

g

ateway

gateway

>

Current IP
Address, Mask,
and Gateway
Address.

Installs a new fixed IP address to be utilized by the Chassis Controller.
This command completes in approximately 15 seconds but does not
require rebooting of the PSA chassis for the new address to take affect.

ipaddress

is the new IP address that will be utilized by the Chassis

Controller in the format of nnn.nnn.nnn.nnn.

m

ask

keyword indicating that next item is IP address mask.

mask

is the IP mask to be utilized for Internet communications. Format is

nnn.nnn.nnn.nnn. Default is 255.255.255.0 (Class C). Must comply with
IP rules for valid mask values.

g

ateway

keyword indicating that next item is IP gateway address.

gateway

is a gateway address to be utilized for Internet Protocol. Format

is nnn.nnn.nnn.nnn. Default is 000.000.000.000.

psa_flash load

type PVA file

“

filename

”

This command is used for downloading new PVA

test blade

(PVA-3102)

firmware images from a host computer to PSA-3000 (or PVA-3002)
chassis flash memory. (

See

psa_update_fw

for PSA-

1200 chassis’

.)

type PVA

Indicates that a firmware image to be downloaded to the PSA

is targeted for a PVA-3102 blade. (See PSA manual for PSA blade
firmware types.)

filename

local path & file name to be downloaded to the chassis flash

memory. Use forward slashes for directory level delimiters in

filename

.

Enclose in quotes if there are spaces in

filename

.

«
...
90
91
92
93
94
...
»

Summary of Contents for PhyView PVA-3000







































































































































Reviews:

No comments

Related manuals for PhyView PVA-3000

Brand: R&S Pages: 733

Brand: R&S Pages: 369

Brand: Yamaha Pages: 17

Brand: Yamaha Pages: 23

Brand: Yamaha Pages: 16

Brand: Yamaha Pages: 28

Brand: Yamaha Pages: 19

Brand: Yamaha Pages: 57

Clavinova CVP-204

Brand: Yamaha Pages: 56

disklavier Mark III Series

Brand: Yamaha Pages: 50

Brand: Yamaha Pages: 23

Brand: ZHYQ Pages: 6

Brand: Burkert Pages: 192

Brand: Palstar Pages: 37

Brand: LD Didactic Pages: 2

Brand: Rae Pages: 38

Brand: FlowLine Pages: 2

Brand: IDEAL Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands