Sifos Technologies PhyView PVA-3000 Reference Manual Download Page 110 | Manualshive

Page: 110 / 134

background image

PVA-3000 Reference Manual

December 2, 2019

Sifos Technologies

Page
110

The

pva_caps

test evaluates

Link Stability

at each supported connection polarity (MDI/MDI-X) for each advertised

link rate (10/100/1000), duplex mode (half, full), and 1000BaseT timing mode (master, slave). The table below
describes each of the reported parameters from the

pva_caps

test.

Parameter

Value

Meaning

AUTO-NEG

NO

DUT does not support Auto-Negotiation

BASE

DUT supports Auto-Negotiation, but does not support Next Page Capability

EXTENDED

DUT supports Auto-Negotiation, including Next Page Capability

ACKS

N/A

Auto-Negotiation information not available

BASE

Link code word received

EXTENDED

Link code word received, Next Page Acknowledge received

NO

No acknowledgements received

1000BaseT

NO

DUT does not support 1000Base-T

HALF

DUT supports 1000Base-T Half Duplex only

FULL

DUT supports 1000Base-T Full Duplex only

HALF+FULL

DUT supports 1000Base-T Half Duplex and Full Duplex

N/A

Link not established

100BaseTX

NO

DUT does not support 100Base-TX

HALF

DUT supports 100Base-TX Half Duplex only

FULL

DUT supports 100Base-TX Full Duplex only

HALF+FULL

DUT supports 100Base-TX Half Duplex and Full Duplex

10BaseT

NO

DUT does not support 10Base-T

HALF

DUT supports 10Base-T Half Duplex only

FULL

DUT supports 10Base-T Full Duplex only

HALF+FULL

DUT supports 10Base-T Half Duplex and Full Duplex

100BaseT4

NO

DUT does not support 100Base-T4

YES

DUT does support 100Base-T4

Pause

NO

DUT does not support Pause operation

RESPOND

DUT capable of full duplex pause operation

XMIT

DUT desires asymmetric pause

XMIT

DUT desires asymmetric pause, capable of full duplex pause operation

Link_OK

FAULT

DUT has detected remote fault

YES

Link is OK

N/A

Could not be assessed

GIG_ERR

MASTER/SLAVE configuration fault detected

MDI / MDI-X

AUTO

DUT supports both MDI and MDI-X

MDI_ONLY

DUT support MDI only

MDI-X_ONLY

DUT support MDI-X only

NLP_Link

LINKED

DUT is able to link to non-auto-negotiating (10Base-T, Half-Duplex) partner

UNLINKED

DUT requires auto-negotiation in order to link

Rx_OK

NO

DUT Remote Receiver (1000Base-T) indicates Not OK

YES

DUT Remote Receiver (1000Base-T) indicates OK

N/A

Could not be assessed

– not applicable

Gig_Mode

AUTO

DUT supports both MASTER and SLAVE configuration

MASTER_ONLY

DUT supports both MASTER configuration only

SLAVE_ONLY

DUT supports both SLAVE configuration only

N/A

Could not be assessed

– not applicable

M-S Fault

NONE

Auto-Resolution of MASTER / SLAVE did not produce a Fault indication

FAULT

Auto-Resolution of MASTER / SLAVE produced a Fault indication

N/A

Could not be assessed

– not applicable

Mstr_Fault

NONE

Forced MASTER timing (link partner = SLAVE) did not produce Fault indicator

FAULT

Forced MASTER timing (link partner = SLAVE) produced a Fault indication

N/A

Could not be assessed

– not applicable

Slv_Fault

NONE

Forced SLAVE timing (link partner = MASTER) did not produce Fault indicator

FAULT

Forced SLAVE timing (link partner = MASTER) produced a Fault indication

N/A

Could not be assessed

– not applicable

«
...
108
109
110
111
112
...
»

Summary of Contents for PhyView PVA-3000







































































































































Reviews:

No comments

Related manuals for PhyView PVA-3000

Brand: AccuMASTER Pages: 2

Brand: LaMotte Pages: 2

Brand: ICT Pages: 48

Brand: OfiTE Pages: 67

Brand: Bacharach Pages: 28

BML SL1-ALZ-ZZ Series

Brand: Balluff Pages: 26

Brand: Abus Pages: 168

Brand: OHAUS Pages: 76

Brand: Yamaha Pages: 6

Brand: YOSensi Pages: 27

Brand: Dynojet Pages: 88

Brand: VP instruments Pages: 15

Brand: Lasertec Pages: 28

WARREN ELLIS SIGNATURE TENOR BARITONE

Brand: Eastwood Guitars Pages: 4

Brand: Fluke Pages: 32

Brand: Omega Pages: 22

Brand: madbeanpedals Pages: 2

Brand: VITO Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands