manualshive.com logo in svg

Sifos Technologies PhyView PVA-3000, Reference Manual

Share
Download
Sifos Technologies PhyView PVA-3000 Reference Manual Download Page 107

PVA-3000 Reference Manual 

December 2, 2019

 

                                   

Sifos Technologies

  

Page 
107 

 
Conclusion: This example shows a loss of 

1371 packets

 (0.13%). 

# Example 7 script 
# Using PVA-3102 in slot,port 1,1 for Tx, 1,2 for Rx 

set TxPort 1,1 
set RxPort 1,2 

 

# Configure both Test Ports for 1000Base-T, duplex, polarity auto, 
gig_mode 
#   Slave so DUT will be Master 

pva_speed

 $TxPort 1000 duplex auto arm 

pva_polarity 

$TxPort auto arm 

pva_gig_mode 

$TxPort slave arm 

pva_speed

 $RxPort 1000 duplex auto arm 

pva_polarity 

$RxPort auto arm 

 

# Force a re-link, to establish the desired line conditions. 

pva_relink

 $TxPort 

pva_relink

 $RxPort 

 

# Verify that the links are up. 

pva_link_wait 

$TxPort 

pva_link_wait

 $RxPort 

 

# Configure impairments on the TxPort. 

pva_line 

$TxPort impair all 

pva_noise 

$TxPort on dB 4.0 

pva_tx_clk 

$TxPort jitter dB 2.0 offset 0 

 

# Start the Received Packet Counter on the RxPort. 

set rslt [

pva_rx_pkt 

$RxPort start] 

 

# Transmit 1024k packets with the TxPort 

set rslt [

pva_tx_pkt

 $TxPort size 60 rate line count 1024K start] 

 

# Check for Transmit completed 

while {[lindex [

pva_tx_pkt

 $TxPort stat] 3] != "IDLE"} { } 

 

# Read the Received Packet Counter. 

set rcvdPackets [lindex [

pva_rx_pkt

 $RxPort stat] 6] 

 

# Stop the Received Packet Counter. 

set rslt [

pva_rx_pkt 

$RxPort stop] 

 

# Calculate Packet Loss. 

set lostPackets [expr 1048576 - $rcvdPackets] 

Figure 4.12

 Example 7 Script Results 

Summary of Contents for PhyView PVA-3000







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands