manualshive.com logo in svg

Sifos Technologies PhyView PVA-3000, Reference Manual

Share
Download
Sifos Technologies PhyView PVA-3000 Reference Manual Download Page 7

PVA-3000 Reference Manual 

December 2, 2019

 

                                   

Sifos Technologies

  

Page 7 

1. 

The PhyView Analyzer & Ethernet PHY Testing 

1.1. 

PVA-3000 Overview 

The PVA-3000 PhyView Analyzer is designed to bridge the wide coverage gap between comprehensive Ethernet 
twisted pair PHY compliance testing and rudimentary link verification testing.  The PVA-3000 introduces an 
innovative, multi-port capability dedicated to 10/100/1000BaseT physical layer characterization under controlled 
impairments including line loss, ingress noise, jittered or offset timing, and even Power-over-Ethernet.  The PVA-3000 
tests Ethernet switches and routers, discrete LAN interfaces, link transmission components, and network service 
integrity at any DTE interface. 
 
The key benefits provided by the PVA-3000 are high testing productivity and quality assurance that comes about from 
a comprehensive range of measurements and analyses. 

1.1.1. 

Test Productivity 

The PhyView Analyzer performs an array of transmitter, interface, and receiver measurements on any 
10/100/1000BaseT Ethernet port using a direct RJ-45 plug connection.  In combination with the PHY Performance Test 
Suite, all testing is fully automated and can be sequenced over 24 DUT ports (

or 96 gigabit pairs

) with a single click of 

a mouse.   Comprehensive, colorful, and graphical spreadsheet reports are automatically generated for each device-
under-test (DUT) port tested.   There are no special requirements of DUT ports – so long as they can link they can be 
fully analyzed by the PhyView Analyzer. 

1.1.2. 

Quality Assurance 

For years, engineers and technicians have been constrained by a wide test coverage gap between true IEEE 802.3 
physical layer qualification and simple link, or packet flow tests that demonstrate basic functionality with very limited 
parametric insight and diagnostic visibility.  At one extreme, traditional physical layer testing is very comprehensive 
but is also expensive, time consuming – typically one pair at a time, and requires significant expertise.  Often, these 
tests are not achievable unless DUT’s are placed in special testing modes not available to commercially packaged 
10/100/1000BaseT ports.   
 
At the other extreme, link-ups and packet flows can be achieved rather easily and inexpensively.  However, this type 
testing seldom quantifies any characteristic of performance while relying on “unknowns” testing “unknowns” under 
“uncharacterized” conditions. 
 
The PhyView Analyzer fills this wide coverage and productivity gap.   Measurements such as transmitter power levels, 
transmitter frequency shaping, and signal-to-noise ratio offer quantitative insights into transmission performance 
without any more effort than it takes to perform basic link tests and simple packet flows.  Interface measurements such 
as Return Loss and Crosstalk flag defects that would otherwise serve as hidden impairments.  Receivers are 
characterized under controlled stresses such as worst case insertion loss, alien crosstalk (ingress noise), timing offsets, 
and random jitter.  Fully automated stressed receiver tests are performed either with packet flow or link monitor 
methods on DUT’s with individual ports as well as multi-port devices such as switches, routers, and repeaters. 

1.1.3. 

Configurations 

The PVA-3000 is provided in one of two configurations: 

 

 

PVA-3000 multi-blade chassis with 12 slots and test capacity of 2 to 24 ports 

 

PVA-3002 two-port, Compact Analyzer 

 
Both configurations offer identical per-test-port features and run from a common host software environment. 
 
The 

PHY Performance Test Suite

 is sold as a soft-key enabled option to any PVA-3000 configuration. 

1.1.4. 

The PowerSync Analyzer Family of Instruments 

The PhyView Analyzer is a member of the PowerSync Analyzer (

PSA

) family of test instruments from Sifos 

Technologies.  The PowerSync Analyzer (PSA-3000) is the industry leader for Power-over-Ethernet (PoE) verification, 
analysis, and testing. 
 
The PVA-3000 consists of a 

PSA-3000

 chassis with one or more 

PVA-3102

 test blades.  The 12-slot PSA-3000 chassis 

can host any combination of PVA-3102 (PhyView Analyzer) and PSA-3202 (PowerSync Analyzer) adding up to 12 
test blades.   The 

PVA-3002

 consists of a single-slot PSA-3002 controller packaged with a single, 2-port PVA-3102 

test blade.   From a features and control point of view, the PVA-3002 is identical to a PVA-3000 with a single PVA-
3102 test blade in test slot #1. 

 

Summary of Contents for PhyView PVA-3000







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands