Sifos Technologies PhyView PVA-3000 Reference Manual Download Page 83 | Manualshive

Page: 83 / 134

background image

PVA-3000 Reference Manual

December 2, 2019

Sifos Technologies

Page
83

Command

Port

Command Parameters

Query

Returned
Parameters

pva_psd

<

port

>

<

trig off

|

ext

> <

pair

pairNo

> <

link 100

|

1000

> <

start

fstart

> <

stop

fstop

> <

avg

nAvgs

> <

timeout 10

|

100

>

stat

READY

+

List of 33 Frequency
& Amplitude (dB)
points

|

ARMED

|

MEASURING

|

TIMEOUT

|

LINK_DROP

|

UNLINKED

|

DISCONNECTED

Configures and performs a Power Spectral Distortion (PSD)
measurement using the calibration data previously acquired
for specified LAN pair, test port, and PVA instrument, and link
speed. Measurement may be either immediate or event
triggered. Configurations are retained in test port and in
PowerShell PSA software.

PSD measurements can be configured over a user selected
frequency range and will always return 33 discrete frequency
– amplitude (in dB) values.

trig off

Configures measurement to start immediately upon

stat

query. (

Test Port wake-up default

)

trig ext

Configures measurement to start upon receipt of the

first Event Trigger following a

stat

query.

pair

pairNo

Specifies LAN PAIR to measure. Range is 1 to 4

where Pair 1 is TIA blue pair, Pair 2 is TIA orange pair, Pair
3 is TIA green pair, and Pair 4 is the TIA brown pair. If link
is 100BaseT, only Pair 2 or 3 may be specified and
depending on pair number, link will be forced to MDI_X or
MDI respectively. (

This configuration is not maintained if

PSA Software is closed

.

PSA Software wake-up default

=

3.)

link 100

Specifies a measurement using 100BaseT. (

This

configuration is not maintained if PSA Software is closed.
PSA Software wake-up default.)

link 1000

Specifies a measurement using 1000BaseT.

(This

configuration is not maintained if PSA Software is closed. )

start

fstart

Specifies start frequency for frequency response

analysis. Range is 0.02 MHz to 80 MHz.

(This

configuration is not maintained if PSA Software is closed.
PSA Software wake-up default = 1 MHz.)

stop

fstop

Specifies end frequency for frequency response

analysis. Range is 0.2 MHz to 100 MHz.

(This

configuration is not maintained if PSA Software is closed.
PSA Software wake-up default = 100 MHz.)

avg

nAvgs

Specifies the number of raw measurements to

average into each channel response coefficient. Range is
1 to 64. If

fstart

is less than 1 MHz,

nAvgs

must be between

48 and 64. (

Test Port wake-up default = 10.

)

timeout 10

specifies that an Event Triggered measurement

should time out if no trigger is received within 10 seconds
following

stat

query. (

Test Port wake-up default

)

timeout 100

specifies that an Event Triggered measurement

should time out if no trigger is received within 100 seconds
following

stat

query.

?

Trigger_Mode (

off

|

ext

)

+

pairNo

+
Link_Speed (

100

|

1000

)

+

fstart

+

fstop

+

nAvgs

+
Timeout

10

|

100

«
...
81
82
83
84
85
...
»

Summary of Contents for PhyView PVA-3000







































































































































Reviews:

No comments

Related manuals for PhyView PVA-3000

Stage Piano MP8

Brand: Kawai Pages: 70

Brand: jenway Pages: 52

Brand: Yamaha Pages: 14

Disklavier Mark II XG Series

Brand: Yamaha Pages: 12

Brand: Hama Pages: 16

Brand: Burkert Pages: 192

Brand: WIKA Pages: 88

Brand: Teledyne Lecroy Pages: 4

Brand: Vectronics Pages: 2

Brand: Resol Pages: 24

AirCon Service Mini Identifier R-1234yf

Brand: Waeco Pages: 132

Brand: Seneca Pages: 2

Brand: E+E Elektronik Pages: 36

Brand: Cal Test Electronics Pages: 14

Brand: Southland Pages: 36

Vertex III V1.5

Brand: Haglof Pages: 24

Brand: Hantek Pages: 58

Brand: Parker Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands