manualshive.com logo in svg

Sifos Technologies PhyView PVA-3000, Reference Manual

Share
Download
Sifos Technologies PhyView PVA-3000 Reference Manual Download Page 59

PVA-3000 Reference Manual 

December 2, 2019

 

                                   

Sifos Technologies

  

Page 
59 

Finally, It should be noted that PowerShell PSA is a more capable environment for running “sequences of sequences”, 
for example, cueing up three PHY Performance Test Suite sequences to test three different DUT’s using one or more 
PVA instruments to produce three separate 

Spreadsheet

 reports. 

3.12.3. 

The DC Unbalance Analysis Application for PSE’s 

A separate and distinct application within the PHY Performance Test Suite is the 

DC Unbalance Analyzer

 for Power 

Sourcing Equipment (PSE’s).  This test is specially formulated to analyze the impact of large DC currents coupled onto 
Ethernet twisted pairs for the delivery of PoE (Power-over-Ethernet).  The testing performed is therefore specific to 
PSE’s and must be performed using two additional components: 

 

1.

 

A Sifos Technologies PSA-3000, PSA-3002, or PSL-3000 PoE analyzer 

7.

 

A Sifos Technologies PVA-DCU In-Line DC Unbalance Channel 

 

The DC Unbalance Analyzer is explained further in Section 5.6. 

 

There are several configuration settings required before running the DC Unbalance Analyzer (

see Figure 3.34

): 

 

PSA (PoE test blade) IP Address

:  This is the address of the PSA-3000, PSA-3002, or PSL-3000 that will be used for 

powering up the PSE port and varying the degree of DC Unbalance load current.  This address could be the same as the 
current PVA instrument address if the test blades are co-located in the same chassis. 
 

PSA Slot,Port

:  This is the PoE test port to be utilized during the analysis entered as in “slot,port” format. 

 

PSE Type

:  This is the type of PSE according to the IEEE 802.3at standard.  

Type 1

 is a 15.4 watt capable PSE,      

Type 2 PHY

 is a 30 watt capable PSE that uses 2-event classification, and 

Type 2 LLDP

 is a 30 watt capable PSE that 

uses LLDP for powered device classification.  (

Note:

 

Type-2 LLDP

 specification will required that the PSA 

instrument be enabled for the LLDP emulation feature.) 

 

Max Unbalance (mA)

:  This is the maximum 

amount of DC Unbalance current that will be 
created as the DC Unbalance Analyzer runs.  
Measurements will be conducted at various 
values of DC Unbalance Current (

see Section

 

5.6

) between a minimum of 30mA up to the 

specified maximum value (

80mA max

.). 

 

Plot Outputs

:  When checked, this option will cause the DC Unbalance Analyzer to automatically pop open a 

spreadsheet report with graphical depictions of Low Frequency PSD and SNR versus DC Unbalance load. 
Results of the DC Unbalance Analyzer will also be displayed in the Results display area. 

3.13.  Calibrations Menu 

The final tab menu within the PVA Interactive tab menu is the 

Calibrations

 menu (

see Figure 3.35

).  From this menu, 

fully automated calibrations of 

PSD

, 

Echo

, and 

Xtalk

 meters are performed.   The calibrations also include 

verifications of PVA impairment 
generators.   All calibrations done from 
this menu will automatically sequence 
across pairs.  Beyond that, calibrations can 
sequence across 

Meters

, 

Link Speeds

, and 

test 

Ports

 with the only restriction being 

that only one test port per test blade (or per 
PVA-3002 instrument) can be calibrated in 
a single sequence. 
 
The meter calibration process, including 
test cables and physical hookups, was 
described earlier in Section 2.2.6. 

 

Calibration sequence configuration 
involves selections for 

Meters

, 

Link 

Speed

, test 

Ports

, and 

Averages

. Meter 

options are 

PSD

, 

Echo

, and/or 

Xtalk

.  

Crosstalk (

Xtalk

) calibrations must be 

preceded by 

Echo

 calibrations on each test 

port, however both may be included in the 
same sequence. 

Figure 3.34

 

DC Unbalance Application for PSE’s 

Figure 3.35

  PVA Interactive Calibrations Menu 

Summary of Contents for PhyView PVA-3000







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands