Sifos Technologies PhyView PVA-3000 Reference Manual Download Page 78 | Manualshive

Page: 78 / 134

background image

PVA-3000 Reference Manual

December 2, 2019

Sifos Technologies

Page
78

Command

Port

Command Parameters

Query

Returned
Parameters

pva_polarity

<

port

>

auto

|

mdi

|

mdi-x

<

arm

>

LINKED |

UNLINKED |

ARMED

Configures Test PHY to advertise selected pair function
through either an immediate re-link (default) or through a
re-link to occur later. Note: Use command

pva_relink

to

initiate the link change if “arm” is specified. Use

pva_link_mon

to query link status. Returns

LINKED

if re-

link is successful, returns

UNLINKED

if re-link fails, and

returns

ARMED

if ‘

arm

’ specified. Accepts broadcast

port

=

99,99 only in combination with

arm

.

auto

Configure connections to whatever the link partners

automatically decide

mdi

Force Test PHY to “MDI” pair functions

mdi-x

Force Test PHY to “MDI-X” pair functions

arm

Configure pair functions but suppress the auto-

negotiation to the configuration until a later re-link
operation. Enables use with port ‘99,99’.

?

AUTO

| MDI |

MDI-X

?

AUTO

| MASTER |

SLAVE

pva_gig_mode

<

port

>

auto

|

master

|

slave

<

arm

>

LINKED_<mode>
|
LINKED_<speed>

| UNLINKED

|

ARMED

Configures Test PHY to allow automatic determination of
1000BaseT Master/Slave or forces Test PHY to either
timing Master or Slave mode. Note: Use command

pva_relink

to initiate the link change if “

arm

” is specified.

Use

pva_link_mon

to query link status. Returns

LINKED_<gig_mode>

if re-link at 1000BaseT is

successful, LINKED_<speed> if re-link is to 100BaseT or
10BaseT, or returns

UNLINKED

if re-link fails, and returns

ARMED

if ‘

arm

’ specified. Accepts broadcast

port

= 99,99

only in combination with

arm

argument.

auto

Configure Master / Slave relationship during link up

master

Force local Test PHY to be Master

slave

Force local Test PHY to be Slave

arm

Configure 1000BaseT timing mode but suppress the

link up to effect this until a later re-link operation.
Enables use with port ‘99,99’.

?

AUTO

| MASTER |

SLAVE

pva_test_signal

<

port

>

off

|

1

|

levels

|

2

|

jitter

|

3

|

4

|

random

|

idle

?

OFF

|

TEST_1  |
TEST_2  |
TEST_3  |
TEST_4

Configures Test PHY to immediately turn on or off a gigabit
test signal. Accepts broadcast

port

= 99,99.

off

Remove gigabit test signal and re-link using any current

link configuration (

wake-up default

)

1

or

levels

Turn on gigabit Test Signal #1 used for pulse

level and droop analysis

2

or

jitter

Turn on gigabit Test Signal #2 used for MASTER

mode jitter analysis

3

Turn on gigabit Test Signal #3 used for SLAVE mode

jitter analysis

4

or

random

Turn on Test Signal #4 used for distortion

analysis

idle

Turn on 100BaseT IDLE transmission signal. Signal

will appear on Pair 2 if in MDI or Pair 3 if in MDI-X.

pva_get_link_

state

<

port

>

LINKED | DOWN

Query returns present link state of current or specified test
port. A disconnected port will report

DOWN

.

pva_get_link_

speed

<

port

>

10 | 100 | 1000 |
UNDETERMINED

Query returns present link rate of current or specified test
port. An unlinked port will report

UNDETERMINED

.

pva_get_gig_

state

<

port

>

MASTER | SLAVE
| FAULT

Query returns present configured gigabit Ethernet timing
mode of current or specified test port. Value is only
meaningful when linked 1000BaseT.

FAULT

indicates

problem with resolving gigabit timing mode.

«
...
76
77
78
79
80
...
»

Summary of Contents for PhyView PVA-3000







































































































































Reviews:

No comments

Related manuals for PhyView PVA-3000

Brand: Badger Meter Pages: 47

Brand: Roland Pages: 15

Brand: KROHNE Pages: 34

Brand: Yamaha Pages: 72

Brand: Yamaha Pages: 5

Brand: Yamaha Pages: 16

Brand: Yamaha Pages: 8

Brand: Yamaha Pages: 7

Brand: Yamaha Pages: 60

GranTouch Digital Grand Piano

Brand: Yamaha Pages: 19

Brand: Yamaha Pages: 44

Brand: Yamaha Pages: 29

Brand: Yamaha Pages: 47

Brand: lanry Pages: 2

Brand: lanry Pages: 29

Brand: Hama Pages: 16

Brand: Lutron Electronics Pages: 13

Brand: Circutor Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands