Siemens SITRANS LR 300 Instruction Manual Download Page 42

Page: 42 / 140

Page 40

SITRANS LR 300 – INSTRUCTION MANUAL

7ML19985CL02

mmmmm

art U

* Pressing

plus three-digit parameter number, sets parameter to show in the

auxiliary display.

Key

Programming Mode

Run Mode

Values

mA output value displayed in auxiliary
reading field

Internal enclosure temperature displayed
in auxiliary reading field (P343).

Decimal point

Parameter for auxiliary readings*

Negative value

Clear value

Toggle between Units and
% on parameter value

Toggle between Units and % on reading
display

End PROGRAM session
and enable RUN mode

Initiate and complete PROGRAM mode
access

Update echo quality
parameters

Distance displayed in auxiliary reading
field.

Parameter scroll-up

Parameter scroll-down

Toggle fields

Enter the displayed value

SITRANS LR 300.book Page 40 Monday, June 10, 2002 7:18 PM

Summary of Contents for SITRANS LR 300













































































































































Search results

Summary of Contents for SITRANS LR 300

Reviews:

Siemens SITRANS LR 300, Instruction Manual, Page: 42 / 140

Search results

Summary of Contents for SITRANS LR 300

Reviews: