manualshive.com logo in svg

Siemens SITRANS LR 300, Instruction Manual, Page: 22 / 140

Share
Download
Siemens SITRANS LR 300 Instruction Manual Download Page 22

Page 20

SITRANS LR 300 – INSTRUCTION MANUAL

7ML19985CL02

mmm

mm

Inst

allat

ion

Dimensions: Waveguide

Notes:

• You can connect a maximum of two waveguides together.
• This option is recommended only for clean liquids on vessels without agitators or 

turbulence. 

• Horizontal stress on this antenna must be avoided, otherwise mechanical support 

may be required. 

• Process temperature and pressure capabilities are dependent upon information on 

the process device tag. Reference drawing listed on the tag is available upon 
request.

• The Process Device Tag shall remain with the process pressure boundary assembly. 

In the event the instrument package is replaced, the Process Device Tag shall be 
transferred to the replacement unit.

WARNING: The user is responsible for the selection of bolting and 

gasket materials which will fall within the limits of the flange and 

its intended use and which are suitable for the service conditions.

process device

 tag

variable min: 100mm (4.08”)

max: 3000mm (122.5")

76.2mm

(3.0”)

waveguide

 41.4mm

(1.69”)

SITRANS LR 300.book  Page 20  Monday, June 10, 2002  7:18 PM

Summary of Contents for SITRANS LR 300













































































































































Reviews:

No comments