manualshive.com logo in svg

Siemens SITRANS LR 300, Instruction Manual, Page: 40 / 140

Share
Download
Siemens SITRANS LR 300 Instruction Manual Download Page 40

Page 38

SITRANS LR 300 – INSTRUCTION MANUAL

7ML19985CL02

mmmmm

St

art U

p

Programming

PROGRAM mode has two states: EDIT and DISPLAY. In DISPLAY state, the parameter 
number, parameter type, and parameter value are being displayed. In EDIT state, the EDIT 
icon is also visible, indicating that the device is accepting input into the current field.

You can activate the PROGRAM mode at any time and set parameters to suit the 
application and/or user preferences. Programming can be carried out locally using the 
hand programmer or remotely through one of the communication channels: Dolphin Plus, 
Simatic PDM, HART Master, or Profibus Master.

The instruction examples in this manual use icons from the hand programmer. 

Dolphin Plus, Simatic PDM, HART Master, or Profibus 
Master

Dolphin Plus is a user interface program designed to configure the SITRANS LR 300 from 
a laptop or a desktop PC, using the RS-485 port. With Dolphin Plus you can modify 
parameter values in real time, view process values in graphic form on screen, save 
profiles, and generate instrument configuration reports. To use the Dolphin protocol, 
ensure the serial protocol parameter P770 is set to Dolphin protocol (1). 

Dolphin Plus software is purchased separately. Please contact your Siemens Milltronics 
representative.

Dolphin Plus 
programming interface

Display

Hand-held programmer

150 mm

(6") max.

SITRANS LR 300.book  Page 38  Monday, June 10, 2002  7:18 PM

Summary of Contents for SITRANS LR 300













































































































































Reviews:

No comments