Siemens SITRANS LR 300 Instruction Manual Download Page 39

Page: 39 / 140

7ML19985CL02

SITRANS LR 300 – INSTRUCTION MANUAL

Page 37

mmmm

art

Start Up

Overview

The SITRANS LR 300 has two modes of operation: RUN and PROGRAM.

After you have completed the installation procedures and powered up the
SITRANS LR 300, the unit starts in RUN mode and detects the distance from the
instrument flange to the target in meters. This is the default start-up display mode.

RUN Mode Display

PROGRAM Mode Display

= Normal reading

= Fail-Safe operation

Reading questionable,
appears during fail-safe
operation

Blinking "Heartbeat”,
indicates device is running

Percentage or Units,
dependent on
parameter number

Active Bar graph

representation of

material level,

0 to 100% of Span

Auxiliary reading

Confidence icons

Reading

Blinking “Heartbeat”,
indicates device is running

Parameter type

Inactive

Bar graph

EDIT icon indicates new
value being entered

Parameter value

Parameter number

Programming indicator

Percentage or Units,
dependent on parameter
value

Index value

SITRANS LR 300.book Page 37 Monday, June 10, 2002 7:18 PM

Summary of Contents for SITRANS LR 300













































































































































Search results

Summary of Contents for SITRANS LR 300

Reviews:

Siemens SITRANS LR 300, Instruction Manual, Page: 39 / 140

Search results

Summary of Contents for SITRANS LR 300

Reviews: