manualshive.com logo in svg

Siemens SITRANS LR 300, Instruction Manual, Page: 32 / 140

Share
Download
Siemens SITRANS LR 300 Instruction Manual Download Page 32

Page 30

SITRANS LR 300 – INSTRUCTION MANUAL

7ML19985CL02

mmm

mm

Inst

allat

ion

Mounting: Horn Antennas or Shielded Rod

The end of the horn, or the end of the shield section, should protrude a minimum of 
10mm (0.5”) to avoid interference with the nozzle.

Mounting: Waveguide Antenna 

This option is recommended for products with 

ε

r

 lower than 3. See P655 on page 68 for 

the related propagation factor.

 

Notes: 

• You can connect a maximum of two waveguides together.
• This option is recommended only for clean liquids, and only on vessels without an 

agitator, with no turbulence. 

• Horizontal stress on this antenna must be avoided, otherwise mechanical support 

may be required. 

• Process temperature and pressure capabilities are dependent upon information on 

the process device tag. The reference drawing listed on the tag is available upon 
request.

10 mm (0.5")

10 mm (0.5")

 Vent hole

minimum 80mm (3")

SITRANS LR 300.book  Page 30  Monday, June 10, 2002  7:18 PM

Summary of Contents for SITRANS LR 300













































































































































Reviews:

No comments