Home
/
Siemens
/
M20 Terminal
/
Technical Description

Siemens M20 Terminal, Technical Description

Share

Page: 111 / 234

Siemens M20 Terminal Technical Description Download Page 111

AT command interface

Version 8 dated 15.03.00

111

Siemens Information and Communication Products

5.7

Siemens-defined AT commands for enhanced functions

Self-defined commands do not have to be implemented in accordance with the official syntax. The "+C" string can there-
fore be replaced by "^S" ("^" = 0x5E). If a self-defined command with the same syntax is to be included in future in the
GSM recommendations, the command can be addressed with both strings.

5.7.1

List of commands

Table 5-4

Siemens-defined AT commands

5.7.2

Detailed description

List of Siemens-
defined commands

Function

AT^SACM

Advice of Charge and query of ACM and ACMmax

AT^SCID

Display SIM card identification number

AT^SCKS

Set SIM conn. presentation. mode and query SIM conn. status

AT^SCNI

List Call Number Information

AT^SCTM

Set critical operating temp. present. mode or query temp.

AT^SLCK

Facility lock (including Siemens-defined locks)

AT^SMGL

List SMS messages from preferred storage without changing status to read

AT^SMGO

Set or query SMS overflow present. mode or query SMS overflow

AT^SMGR

Read SMS message without set to REC READ

AT^SMSO

Switch off mobile station

AT^SNFA

Set or query of microphone attenuation

AT^SNFE

Set or query echo suppression parameters

AT^SNFI

Set microphone path parameters

AT^SNFM

Mute microphone

AT^SNFO

Set or query audio output (= loudspeaker path) parameters

AT^SNFS

Select audio hardware set

AT^SNFV

Set or query loudspeaker volume

AT^SPIC

Display PIN counter

AT^SPLM

Read the PLMN list

AT^SPLR

Read entry from the preferred operator list

AT^SPLW

Write an entry to the preferred operator list

AT^SPWD

Change password for a lock (including Siemens-defined locks)

AT^SRTC

Select, query or test ringing tone

AT^MONI

Monitor mode in Idle mode

AT^MONP

Monitor neighbour cells

AT+CXXCID

Display card ID (identical to AT^SCID)

AT^SACM

Advice of charge and query of ACM and ACMmax

Test command

AT^SACM=?

Response

^SACM: (list of supported <n>s) OK

Parameter

see set command

«
...
109
110
111
112
113
...
»

Summary of Contents for M20 Terminal











































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands