Siemens M20 Terminal Technical Description Download Page 48

Page: 48 / 234

AT command interface

Version 8 dated 15.03.00

Siemens Information and Communication Products

AT+DS

V.42bis data compression control

Test command

AT+DS=?

Response

+DS: (list of supported <p0>s), (list of supported <n>s), (list of supported <p1>s), (list of suppor-
ted <p2>s) OK

Parameter

see set command

Read command

AT+DS?

Response

+DR: <p0>,<n>,<p1>,<p2> OK

Parameter

see set command

Set command

AT+DS=[<p0>[,<
n>[,<p1>[,<p2>]]]]

Response

This parameter setting determines the possible data compression mode by TA at the compression
negotiation with the remote TA after call setup.

Note1

: only for data call

Note2

: GSM transmits the data transparent. The remote TA may support this compression.

Parameter

Note:

Summary of Contents for M20 Terminal











































































































































































































































Search results

Summary of Contents for M20 Terminal

Reviews:

Related manuals for M20 Terminal

Brands by name

Popular brands

Siemens M20 Terminal, Technical Description

Search results

Summary of Contents for M20 Terminal

Reviews:

Related manuals for M20 Terminal

Brands by name

Popular brands