manualshive.com logo in svg

Siemens M20 Terminal, Technical Description

Share
Download
Siemens M20 Terminal Technical Description Download Page 33

AT command interface

Version 8 dated 15.03.00

33

Siemens Information and Communication Products

A

ATD><mem><n> Originate call to phone number <n> in memory <mem>

Execute command

ATD><mem>
<n>[<I>][<G>][;]

Response

TA attempts to set up an outgoing call to stored number.

e.g.: ATD>SM5;    Voice call to number at position 5 on the SIM phonebook.

Note:

 this command may be aborted generally by receiving a character during execution. This com-

mand cannot be aborted in some connection setup states, such as handshaking.

If error is related to ME functionality

+CME ERROR: <err>

If no dialtone and (parameter setting X=2 or X=4)

NO DIALTONE 

If busy and (parameter setting X=3 or X=4)

BUSY

If a connection cannot be set up
NO CARRIER

If successfully connected and non-voice call
CONNECT<text> 

Note:

 <text> only if parameter setting X>0

TA switches to data state.
When TA returns to command mode after call release

OK

If successfully connected and voice call
OK

Parameter

<mem>

phonebook:

FD

SIM fixdialling-phonebook

LD

SIM last-dialling-phonebook

RC

ME received calls list

MC

ME missed (unanswered received) calls list

SM

SIM phonebook

ON

SIM (or ME) own numbers (MSISDNs) list

ME

ME phonebook

MT

Combined ME and SIM phonebook

<n>

integer type memory location should be in the range of locations available in the me-
mory used

<I>

I

CLIR invocation

i

CLIR suppression

<G>

G, g

CUG info, uses set with command +CCUG

<;>

voice call, return to command state

Reference

V.25ter/GSM 
07.07

Note

Emergency call: no SIM needed

<n> 112 worldwide number

There is no <mem> for emergency call ("EN").

Summary of Contents for M20 Terminal











































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands