manualshive.com logo in svg

Siemens M20 Terminal, Technical Description

Share
Download
Siemens M20 Terminal Technical Description Download Page 83

AT command interface

Version 8 dated 15.03.00

83

Siemens Information and Communication Products

A

AT+CR

Service reporting control

Test command

AT+CR=?

Response

+CR: list of supported <mode>s OK

Parameter

see set command

Read command

AT+CR?

Response

+CR: <mode> OK

Parameter

see set command

Set command

AT+CR=<mode>

Response

TA controls whether or not intermediate result code +CR: <serv> is returned from the TA to the 
TE at call setup.

OK

Parameter

<mode>

0

disable

1

enable

Intermediate result code

When enabled, an intermediate result code is transmitted at the point during connect negotiation 
when the TA has determined the speed and quality of service will be used, before any error control 
or data compression reports are transmitted, and before any final result code (e.g. CONNECT) is 
transmitted.

+CR:<serv>

Parameter

<serv>

ASYNC

asynchronous transparent

SYNC

synchronous transparent

REL ASYNC

asynchronous non-transparent

REL SYNC

synchronous non-transparent

Reference

GSM 07.07

Note

The PLMN influences the second air interface (to the terminator), therefore another mode may be 
established from the network

Summary of Contents for M20 Terminal











































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands