Siemens M20 Terminal Technical Description Download Page 32 | Manualshive

Page: 32 / 234

Siemens M20 Terminal Technical Description Download Page 32

AT command interface

Version 8 dated 15.03.00

32

Siemens Information and Communication Products

When <n> is a supplementary service string:

TA attempts to call the supplementary service entered in dialled string.

TA returns result of invoked supplementary service AT command.

Parameter

Reference

V.25ter/
GSM 07.07/02.30

Note

This call command or supplementary service call command may be aborted generally by receiving
a character during execution. This command cannot be aborted in some connection setup states,
such as handshaking.

<n>:

Functionality:

Invoked supp.service:

*#06#

Query IMEI:

+CGSN

**04[2]*oldPin*newPin[2]*newPin[2]#

Change SIM pwd:

+CPWD

**05[2]*unblKey*newPin[2]*newPin[2]# Change/Unblocking SIM pwd:

^SPWD

*[*]03*[ZZ]*oldPw*newPw*newPw#

Registration of net password:

+CPWD

*#30#

Interrogation CLIP

+CLIP

*#31#

Interrogation CLIR

+CLIR

*#76#

Interrogation COLP

+COLP

(choice of *,#,*#,**,##)21*DN*BS#

Act/deact/int/reg/eras CFU

+CCFC

(choice of *,#,*#,**,##)67*DN*BS#

Act/deact/int/reg/eras CF busy

+CCFC

(choice of *,#,*#,**,##)61*DN*BS*T#

Act/deact/int/reg/eras CF no reply

+CCFC

(choice of *,#,*#,**,##)62*DN*BS#

Act/deact/int/reg/eras CF no reach

+CCFC

(choice of *,#,*#,**,##)002*DN*BS*T#

Act/deact/int/reg/eras CF all

+CCFC

(choice of *,#,*#,**,##)004*DN*BS*T#

Act/deact/int/reg/eras CF all cond.

+CCFC

(choice of *,#,*#)43*BS#

Activation/deactivation/int WAIT

+CCWA

(choice of *,#,*#)33*Pw*BS#

Act/deact/int BAOC

+CLCK

(choice of *,#,*#)331*Pw*BS#

Act/deact/int BAOIC

+CLCK

(choice of *,#,*#)332*Pw*BS#

Act/deact/int BAOIC exc.home

+CLCK

(choice of *,#,*#)35*Pw*BS#

Act/deact/int. BAIC

+CLCK

(choice of *,#,*#)351*Pw*BS#

Act/deact/int BAIC roaming

+CLCK

#330*Pw*BS#

Deact. All Barring Services

+CLCK

#333*Pw*BS#

Deact. All Outg.Barring Services

+CLCK

#353*Pw*BS#

Deactivation. All Inc.Barring Services

+CLCK

[C]...[C]#

Send USSD message

+CUSD

C[C] in call

Call hold and multiparty

+CHLD

C[C] (excluded 1[C])

Send USSD message

+CUSD

where
ZZ

type of supplementary services:

Barring services

330

All services

----

DN

dialling number: string of digits 0-9

BS

basic service: Voice

11

Sms

16

Fax

13

Sms+fax

12

Voice+fax

19

Voice+sms+fax

10

Data circuit asyncron

25

Data circuit syncron

24

PAD

27

packet

26

data circuit async.+PAD

21

data circuit sync.+packet

22

data circ.async+sync.+PAD+packet

20

all services

----

T

time in seconds

Pw

net password

C

character of TE character set

«
...
30
31
32
33
34
...
»

Summary of Contents for M20 Terminal











































































































































































































































Reviews:

No comments