Siemens M20 Terminal Technical Description Download Page 126

Page: 126 / 234

AT command interface

Version 8 dated 15.03.00

126

Siemens Information and Communication Products

AT^SNFS

Select audio hardware set

Test command

AT^SNFS=?

Response

^SNFS: (list of supported <n>s) OK

Parameter

see set command

Read command

AT^SNFS?

Response

^SNFS: <n> OK

Parameter

see set command

Set command

AT^SNFS=<n>

Response

TA activates the selected audio mode.

Parameter

<n>

1(0x1)

Audio mode 1: standard mode approved for handset, V38140-H-X33)

3(0x3)

Audio mode3: customer specific mode; all audio parameters can be
adjusted using AT commands

Reference

GSM Engine A1

Note

The command does the same as +VIP. For more details, see relevant section.

AT^SNFV

Set or query loudspeaker volume

Test command

AT^SNFV=?

Response

^SNFV: (list of supported <vol>s) OK

Parameter

see set command

Read command

AT^SNFV?

Response

^SNFV: <vol> OK

Parameter

see set command

Set command

AT^SNFV=<vol>

Response

TA controls the volume of the loudspeaker.

Parameter

<vol>

Volume range (0 to 7)

(0 low...7 max. volume; approx. 3 dB/stage)

Reference

Note

AT^SPIC

Display PIN counter

Test command

AT^SPIC=?

Response

Parameter

Execute command

AT^SPIC

Response

TA returns the number of attempts still available for entering the required password.

Note

: command "AT+CPIN?" to check which password is currently required

^SPIC: <counter> OK

If error is related to ME functionality:

+CME ERROR: <err>

Parameter

<counter>

Number of attempts still available for entering the required password.

Reference

Note

AT^SPLM

Read the PLMN list

Summary of Contents for M20 Terminal











































































































































































































































Search results

Summary of Contents for M20 Terminal

Reviews:

Related manuals for M20 Terminal

Brands by name

Popular brands

Siemens M20 Terminal, Technical Description

Search results

Summary of Contents for M20 Terminal

Reviews:

Related manuals for M20 Terminal

Brands by name

Popular brands