Siemens M20 Terminal Technical Description Download Page 182

Page: 182 / 234

Application notes

Version 8 dated 15.03.00

182

Siemens Information and Communication Products

8.4.2.6

int FlushComm(idComDev, fnQueue)

int idComDev;

/* communications-device identifier

int fnQueue;

/* queue to flush

The FlushComm function flushes all characters from the transmission or receiving queue of the specified communications
device.

int FlushComm(idComDev, fnQueue)

Parameter

Description

idComDev

Specifies the communications device to be flushed. The OpenComm function returns this
value.

fnQueue

Specifies the queue to be flushed. The transmission queue is flushed if this parameter is ze-
ro. The receiving queue is flushed if the parameter is 1.

Return value

0 if the function is successful.

< 0 if idComDev is not a valid device or if fnQueue is not a valid queue

> 0 if there is an error for the specified device. For a list of the possible error values, see the
GetCommError function.

Example

None

Comments

None

See also

GetCommError, OpenComm

Summary of Contents for M20 Terminal











































































































































































































































Search results

Summary of Contents for M20 Terminal

Reviews:

Brands by name

Popular brands

Siemens M20 Terminal, Technical Description

Search results

Summary of Contents for M20 Terminal

Reviews:

Brands by name

Popular brands