Siemens M20 Terminal Technical Description Download Page 171

Page: 171 / 234

Application notes

Version 8 dated 15.03.00

171

Siemens Information and Communication Products

8.2.10.6

Store SMS in memory

8.2.10.7

List of all SMS of the memory

8.2.10.8

Delete SMS message

8.2.10.9

Send SMS stored in the memory

8.2.10.10 Incoming SMS message

8.2.10.11 Read SMS message

8.2.11

WinFaxPro setup

NOTE

:1) The M20 only accepts FAX Protocol T62. Some GSM providers have T61 as the standard protocol.

+cmgs: 29

Counts the messages sent with the SIM card

at+cmgw="+436764910086"

Except for the at – command same procedure

>text of SMS

As for sending (do not forget: CTRL Z (!)

+cmgw:5

Message is stored in position number 5 of your memory

at+cmgl

+cmgl:2,”REC_READ”,”+4366422547661”,”98/07/
28,12:35:23+00”

text of SMS message

Stored in position number 2 is an SMS you have
read, received from phone number, service cen-
tre time-stamp

+cmgl:5,”STO_UNSENT”,”+436764910086”

text of SMS message

An SMS you stored and have not yet sent

...

at+cmgd=2

Deletes message in position 2 of the memory

Delete messages you do not need because you can only store 15
SMSs

and cannot receive new ones if there is no space left

at+cmss=2

Enter the number of an unsent message

+cmss: 30

Counts the messages sent with the SIM card

+CMTI:”SM”,14

Indicates that you have just received an SMS that is stored in posi-
tion 14 of your memory

at+cmgr=14

read SMS in position 14 of the memory

+CMGR:”REC_UNREAD”,”+436641406214”,”98/07/
30,15:15:30+00”

Text of SMS

The status of the SMS is received and un-
read, indicates the sender and when it ar-
rived at the service centre

Summary of Contents for M20 Terminal











































































































































































































































Search results

Summary of Contents for M20 Terminal

Reviews:

Related manuals for M20 Terminal

Brands by name

Popular brands

Siemens M20 Terminal, Technical Description

Search results

Summary of Contents for M20 Terminal

Reviews:

Related manuals for M20 Terminal

Brands by name

Popular brands