Siemens M20 Terminal Technical Description Download Page 106 | Manualshive

Page: 106 / 234

background image

AT command interface

Version 8 dated 15.03.00

106

Siemens Information and Communication Products

AT+CSAS

Save SMS settings

Test command

AT+CSAS=?

Response

+CSAS: (list of supported <profile>s) OK

Parameter

Execute command

AT+CSAS[=
<profile>]

Response

TA saves current message service settings for +CSCA, +CSMP to SIM card.

OK

If error is related to ME functionality:

+CMS ERROR:<err>

Parameter

<profile>

0

manufacturer-specific profile number where settings are to be stored

Reference

GSM 07.05

Note

Only one user profile supported.

Warning: If any SMS values are changed and saved on the SIM using the AT+CSAS command,
then the original values are lost and cannot be reset.

AT+CSCA

SMS service centre address

Test command

AT+CSCA=?

Response

OK

Read command

AT+CSCA?

Response

+CSCA: <sca>,<tosca> OK

Parameter

see set command

Set command

AT+CSCA =
<sca>[,<tosca>]

Response

TA updates the SMSC address, through which mobile originated SMs are transmitted. In text mode,
setting is used by send and write commands. In PDU mode, setting is used by the same commands,
but only when the length of the SMSC address coded into <pdu> parameter equals zero.

OK

Parameter

<sca>

GSM 04.11 RP SC address Address-Value field in string format; BCD numbers (or
GSM default alphabet characters) are converted into characters; type of address gi-
ven by <tosca>

<tosca>

Service centre address format GSM 04.11 RP SC address Type-of-Address octet in
integer format (default refer <toda>)

Note:

If Parameter field <tosca> is ignored, national/international call center numbers are recogni-

zed by the l in the number.

Reference

GSM 07.05

Note

AT+CSCB

Select cell broadcast SMS messages

Test command

AT+CSCB=?

Response

Test command returns supported modes as a compound value.

+CSCB: (list of supported <mode>s) OK

Parameter

see set command

Read command

AT+CSCB?

Response

+CSCB: <mode>,<mids>,<dcss> OK

Parameter

see set command

«
...
104
105
106
107
108
...
»

Summary of Contents for M20 Terminal











































































































































































































































Reviews:

No comments

Related manuals for M20 Terminal

Brand: 3W Pages: 20

Brand: TAYO Pages: 42

Brand: Grundfos Pages: 25

Brand: Briggs & Stratton Pages: 10

Brand: Hatz Diesel Pages: 48

Brand: Onan Pages: 341

Brand: Perkins Pages: 42

Brand: Simple Motors Pages: 6

Brand: Volvo Penta Pages: 84

Brand: Volvo Penta Pages: 88

Brand: Leadshine Pages: 18

Ultimate MX8 Racing

Brand: Modelix Pages: 7

Brand: NSK Pages: 62

Brand: NSK Pages: 110

Brand: Honda Pages: 69

Brand: Honda Pages: 97

Brand: sati Pages: 19

Brand: LONCIN Pages: 224

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands