Siemens M20 Terminal Technical Description Download Page 129

Page: 129 / 234

AT command interface

Version 8 dated 15.03.00

129

Siemens Information and Communication Products

AT^SPWC

List password counter

Execute command

AT^SPWC

Response

TA returns the number of attempts still available for entering the required password.

^SPWC: <code> <counter>

If facility locks are disabled:

^SPWC: SIM PIN 3

^SPWC: SIM PUK 10

^SPWC: SIM PIN2 3

^SPWC: SIM PUK2 10

If facility locks are enabled:

^SPWC: SIM PIN 3

^SPWC: SIM PUK 10

^SPWC: SIM PIN2 3

^SPWC: SIM PUK2 10

^SPWC: PH-SIM PIN 3

^SPWC: PH-NET PIN 3

^SPWC: PH-NETSUB PIN 3

^SPWC: PH-SP PIN 3

^SPWC: PH-CORP PIN 3

If error is related to ME functionality:

+CME ERROR: <err>

Parameter

<code>

SIM PIN

SIM PUK

SIM PIN2

SIM PUK2

PH-SIM PIN (lock PHone to SIM card)

PH-NET PIN Network Personalisation (refer GSM 02.22[33])

PH-NETSUB PIN Network Subset Personalisation (refer GSM 02.22[33])

PH-SP PIN Service Provider Personalisation (refer GSM 02.22[33])

PH-CORP PIN Corporate Personalisation (refer GSM 02.22[33])

<counter>

Number of attempts still available for entering the required password.

Reference

Refer GSM 07.07

Note

Summary of Contents for M20 Terminal











































































































































































































































Search results

Summary of Contents for M20 Terminal

Reviews:

Brands by name

Popular brands

Siemens M20 Terminal, Technical Description

Search results

Summary of Contents for M20 Terminal

Reviews:

Brands by name

Popular brands