Acmeda Automate RF 500 Series Programming Instructions Manual Download

Page: 1 / 8

Electronic Limit Tubular Motor

Electronic

Electronic Limit + Built-in Receiver

433MHz

All controls support 433MHz
All controls support 230V/50Hz

FEB 2014

AUTOMATE EL MOTORS / PROGRAMMING INSTRUCTIONS

These instructions show how to install, program and use Acmeda’s electronic limit tubular motors:

•

Automate EL S45

•

Automate Q EL S45 (quiet motor)

•

Automate EL S60 (with collision control technology)

•

Automate EL A50 (for open awnings)

•

Automate EL A50/C (for cassette awnings)

•

Automate C EL (Curtain motor)

These motors can be controlled with Automate RF 500 series remote devices:

•

Automate RF501 (single channel)

•

Automate RF515 (15 channel)

•

Automate RF505 (5 channel timer)

RF500 series Remote Control

Only use
Acmeda tail

CIRCUIT INSTALLATION

RF5

Summary of Contents for Automate RF 500 Series









Search results

Summary of Contents for Automate RF 500 Series

Reviews:

Related manuals for Automate RF 500 Series

Brands by name

Popular brands

Acmeda Automate RF 500 Series, Programming Instructions Manual

Search results

Summary of Contents for Automate RF 500 Series

Reviews:

Related manuals for Automate RF 500 Series

Brands by name

Popular brands