Siemens M20 Terminal Technical Description Download Page 130 | Manualshive

Page: 130 / 234

background image

AT command interface

Version 8 dated 15.03.00

130

Siemens Information and Communication Products

AT^SPWD

Change password for a lock (including Siemens-defined locks)

Test command

AT^SPWD=?

Response

^SPWD: (list of supported (<fac>, <pwdlength>)s) OK

Parameter

<fac>

see execute command

<pwdlength>

integer

max. length of password

Execute command

AT^SPWD =
<fac>, <oldpwd>,
<newpwd>

Parameter

<fac>

"SC" SIM card (PIN)

"AO" BAOC (Bar All Outgoing Calls)

"OI"

BOIC (Bar Outgoing International Calls)

"OX" BOIC-exHC (Bar Outgoing International Calls except to Home Country)

"AI"

BAIC (Bar All Incoming Calls)

"IR"

BIC-Roam (Bar Incoming Calls when Roaming outside the home country)

"AB" All Barring services

"AG" All outGoing barring services

"AC" All inComing barring services

"P2"

PIN 2

"UP" Unblocking PIN by PUK

"UP2" Unblocking PIN2 by PUK2

<oldpwd>

password specified for the facility from the user interface
or with command. If an old password has not yet been
set, <oldpwd> is not to enter.

if <fac> = "SC" then PIN

if <fac> = "AO"..."AC" (barring) then network password

if <fac> = "P2" then PIN2

if <fac> = "UP" then PUK

if <fac> = "UP2" then PUK2

<newpwd> new

password

Response

All facility locks: AO, OI, OX, AI, IR, AB, AG, AC, have the same <password> to lock and un-
lock. The <password> depends on the network provider.

TA sets a new password for the facility lock function.

OK

If error is related to ME functionality:

+CME ERROR: <err>

Reference

GSM 07.07:
AT+CPWD

Note

AT^SRESET

Software reset

Test command

AT^SRESET

Response

OK

Resetting module

Reference

Note

A software reset is executed with this command, which takes about 4 seconds. It is necessary for a
successful command execution to keep the ignition line high during this operation.

«
...
128
129
130
131
132
...
»

Summary of Contents for M20 Terminal











































































































































































































































Reviews:

No comments

Related manuals for M20 Terminal

Brand: Hacker Pages: 8

Brand: Garmin Pages: 16

Brand: MTU Pages: 153

Brand: PCM Pages: 83

Brand: SEW-Eurodrive Pages: 88

Brand: CAB Pages: 16

Brand: Brother Pages: 42

Brand: ABB Pages: 13

Brand: Leroy-Somer Pages: 8

Brand: Leroy-Somer Pages: 6

MICRO GEARLESS XAP1-CE

Brand: Leroy-Somer Pages: 12

Brand: dunkermotoren Pages: 30

AG2210-LP Series

Brand: Beckhoff Pages: 35

Brand: GMC Pages: 7

Brand: Volvo Pages: 72

Brand: MULTIPLEX modell Pages: 11

Brand: Honda Pages: 156

Brand: O.S. engine Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands