Siemens Gigaset 4000 Comfort Operating Instructions Manual Download Page 97

Page: 97 / 116

Compatibility

Gigaset 4110isdn, GBR, A31008-G4110-B102-2-7619

Kompati.fm

4.9.02

Compatibility

The list shows you which functions of your Gigaset 4000 Classic handset and
other manufacturers’ handsets are supported.
It is possible to register up to 4 Gigaset 4000 Classic handsets.

Function

Gigaset
4000 Classic

Other
manuf.

Registration

Dialling

Provider list/Speed dialling

Charge display

Call duration

Callback

CLIP call number display

Accept call waiting

R key

Reject call waiting

Extending external calls

R key, then
0 key

3-party conference

Toggle

Enquiry call user 1

Enquiry call user 2

Collective call, internal (with automatic line
seizure deactivated)

Seize,

Seize, then *
key

Internal calling (with automatic line seizure
deactivated)

Seize, 11-16

Display new messages

Interrogate missed calls list

Ring tone discrimination per MSN

Number redial

Dialling from local telephone book

Send/receive SMSs

Summary of Contents for Gigaset 4000 Comfort





















































































































Search results

Summary of Contents for Gigaset 4000 Comfort

Reviews:

Related manuals for Gigaset 4000 Comfort

Brands by name

Popular brands

Siemens Gigaset 4000 Comfort, Operating Instructions Manual

Search results

Summary of Contents for Gigaset 4000 Comfort

Reviews:

Related manuals for Gigaset 4000 Comfort

Brands by name

Popular brands