Siemens Gigaset 4000 Comfort Operating Instructions Manual Download Page 102

Page: 102 / 116

101

Menu displays

Gigaset 4110isdn, GBR, A31008-G4110-B102-2-7619

Menue.fm

4.9.02

Base Settings > Forward. netw.

Step 1

Step 2

Step 3

Step 4

MSN1 Call...

New entry

MSN

Immediately

etc.

On busy

On no reply

Activate?

Edit entry

Delete entry

Base Settings > Forward. base

Step 1

Step 2

Step 3

Step 4

Activate?

Deactivate?

Forward. dest.

INT11:Internal11

Display of all available internal numbers.

No. of rings

0 - 9

Base Settings

Night service

Step 1

Step 2

Step 3

Step 4

MSN1 xy...

Activate?

Deactivate?

usw.

Forward. dest.

External

Dest.call no.

Internal

INT11:Internal11

Display of all available internal numbers

Start time:

HH:MM

Save entry

Cancel

End time:

HH:MM

Save entry

Cancel

Sat/Sun all day

Base Settings > Settings > Security

Step 1

Step 2

Step 3

Change PIN

New PIN

Authorisation

INT11:Unrestrict

Display of all available internal numbers.

Unrestricted

Incoming only

Int. only

Emergency nos.

Change number

Delete number

Display number

Summary of Contents for Gigaset 4000 Comfort





















































































































Search results

Summary of Contents for Gigaset 4000 Comfort

Reviews:

Related manuals for Gigaset 4000 Comfort

Brands by name

Popular brands

Siemens Gigaset 4000 Comfort, Operating Instructions Manual

Search results

Summary of Contents for Gigaset 4000 Comfort

Reviews:

Related manuals for Gigaset 4000 Comfort

Brands by name

Popular brands