Siemens Gigaset 4000 Comfort Operating Instructions Manual Download Page 88

Page: 88 / 116

Appendix

Gigaset 4110isdn, GBR, A31008-G4110-B102-2-7619

Anhang.fm

4.9.02

Appendix

Maintenance

Simply wipe the base station and handset with a

damp cloth

or an antistatic

wipe.

Never

use a dry cloth as this can cause static discharge.

Contact with liquid

If the handset should come into contact with liquid,

on no account switch the device on.
Remove all batteries immediately.

Allow the liquid to drip out of the device, and then dab all parts of the device
dry.

Keep the handset with the batteries removed in a warm, dray place for at least
72 hours. In many cases, you will then be able to use it again.

Questions and answers

If any questions occur to you while you are using your device, we are available
24 hours a day at

www.my-siemens.com/customercare.

You will find the

most frequently asked questions and answers below.

Question

Possible cause

Possible solution

The handset does not
ring after the ISDN call
number (MSN) has been
set up.

The local area code was
saved with the MSN.

Save the MSN

without

the local area code
(page 27)

The handset does not
ring.

Ring tone has been
deactivated.

Night service active

Press activate ring
tone

Deactivate night serv-
ice (page 66)

There is no display.

The handset is not
switched on.

Press the replace
handset key

for

1 second

The batteries need
charging.

Charge or replace
the batteries
(page 14).

Nothing happens when I
press the keys.

The keypad lock is
activated.

Press

for

1 second

There’s no radio link to
the base –

ORRNLQJ

IRU EDVH

flashes, for

example.

The handset is outside
the range of the base.

Move the handset and
base closer together.

The handset has not
been registered.

The base is not
switched on.

Check the plug-in power
supply on the base
(page 12).

Summary of Contents for Gigaset 4000 Comfort





















































































































Search results

Summary of Contents for Gigaset 4000 Comfort

Reviews:

Related manuals for Gigaset 4000 Comfort

Brands by name

Popular brands

Siemens Gigaset 4000 Comfort, Operating Instructions Manual

Search results

Summary of Contents for Gigaset 4000 Comfort

Reviews:

Related manuals for Gigaset 4000 Comfort

Brands by name

Popular brands