Siemens Gigaset 4000 Comfort Operating Instructions Manual Download Page 45

Page: 45 / 116

Convenient telephoning

Gigaset 4110isdn, GBR, A31008-G4110-B102-2-7619

Komfortabel.fm

4.9.02

Step

step

Table of symbols

Press the appropriate key several times or use long pressing:

The

initial letter

of the name will

automatically be a capital

(also after a

punctuation mark); it will be followed by lower-case letters.

To change a letter from

upper to lower case

, or vice versa: press

Control

the cursor using

) * ( '

The character to the left of the cursor is

deleted

using

;

Characters are always

inserted

to the left of the cursor.

Entries are sorted in the

following sequence

1. Space

2. Digits: (0–9)
3. Letters (alphabetic)

4. Other characters
To bypass the alphabetic sequence of entries in the telephone directory, insert
a blank in front of the name. That entry will then move to first position (exam-
ple: you could key in “ Karla”).

10x 11x 12x 13x 14x

Space

→

(

)

“

‘

;

}

Info

Summary of Contents for Gigaset 4000 Comfort





















































































































Search results

Summary of Contents for Gigaset 4000 Comfort

Reviews:

Related manuals for Gigaset 4000 Comfort

Brands by name

Popular brands

Siemens Gigaset 4000 Comfort, Operating Instructions Manual

Search results

Summary of Contents for Gigaset 4000 Comfort

Reviews:

Related manuals for Gigaset 4000 Comfort

Brands by name

Popular brands