Siemens Gigaset 4000 Comfort Operating Instructions Manual Download Page 108 | Manualshive

Page: 108 / 116

background image

107

ISDN Glossary

Gigaset 4110isdn, GBR, A31008-G4110-B102-2-7619

Glossar.fm

4.9.02

Calling Line Identification Restriction (CLIR)

Transfer of your own call number is disabled.

CCBS

(Completion of calls to busy subscriber)

See Callback on busy.

CCNR

(Completion of calls no reply)

See Callback on no reply.

CD

(Call Deflection)

See Call deflection

CF

(Call Forwarding)

See Call forwarding

Channel

An ISDN line, like an analogue telephone line, has two cables running into
your house but a distinction is made in ISDN between the two logical user
channels, known as the B-channels (which have nothing to do with the
physical cables) and the control channel, known as the D-channel.

Charge display

See AOC-D and AOC-E.

CLIP

(Calling Line Identification Presentation)

Subscriber A calls subscriber B. The call number of A appears on B's
telephone display.

CLIR

(Calling Line Identification Restriction)

The number of the calling line is not displayed.

COLP

(Connected line identification presentation)

Subscriber A calls subscriber B. The call number of B is displayed on A's
telephone. If B has programmed call forwarding or deflection to C, then the
number dialed and the number transferred will not be the same; the call
number of C will be displayed, provided C has not suppressed his number.

COLR

(Connected line identification restriction)

The call number of C is not displayed on A's telephone if C has set up COLR.

Conference call

See Three-party conference.

CW

(Call Waiting)

See Call waiting

«
...
106
107
108
109
110
...
»

Summary of Contents for Gigaset 4000 Comfort





















































































































Reviews:

No comments

Related manuals for Gigaset 4000 Comfort

Brand: NEC Pages: 42

Brand: NEC Pages: 8

Brand: NEC Pages: 220

Brand: NEC Pages: 2

Brand: Panasonic Pages: 252

Brand: Panasonic Pages: 8

Brand: AT&T Pages: 116

Cordless Telephone

Brand: Radio Shack Pages: 12

DECT2060-2 - DECT Cordless Phone

Brand: Uniden Pages: 56

Brand: BT Pages: 72

Brand: Radio Shack Pages: 24

Brand: Tempo Fitness Pages: 6

Infinite Station

Brand: Vodavi Pages: 38

Brand: AT&T Pages: 40

Auto-Attendant System

Brand: Yosin Pages: 17

Brand: Hama Pages: 14

Brand: Chronos Telecom Pages: 38

Brand: Curtis Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands