Siemens Gigaset 4000 Comfort Operating Instructions Manual Download Page 89

Page: 89 / 116

Appendix

Gigaset 4110isdn, GBR, A31008-G4110-B102-2-7619

Anhang.fm

4.9.02

There is no display of
units/costs.

No charge rate informa-
tion supplied.

Apply to the phone
company to have meter-
ing pulses transmitted.

There is no display of
call costs.

Cost
per unit = 0.

Set cost per unit
(page 67).

I can’t hear anything.

The

)

key has been

pressed – the micro-
phone has been
“muted.”

Press

to resume

your conversation.

The caller’s number is
not displayed.

Call number transmis-
sion has been barred.

The caller must apply
to his/her provider to
enable transmission of
the number.

No numbers can be
dialled.

The long-distance code
has changed.

The phone has been
locked.

Check and correct the
long-distance code
(page 33).

Check the status dis-
plays, unlock the phone if
necessary (page 15).

No calls

are being

received.

“Permanent” call for-
warding has been acti-
vated.

The MSN has not been
assigned to the internal
user.

The “internal” class-of-
service has been set.

Deactivate “perma-
nent” call forwarding
(page 55).

Specify the receive MSN
(page 27).

Change the class-of-ser-
vice (page 79).

The

forwarding condi-

tions

are not displayed

for

call forwarding

Internal forwarding has
been activated.

Activate “external” for-
warding (page 54).

Apply to your provider to
enable this.

The phone also rings
when there are

fax/PC

calls

The call number is in the
base phone’s call num-
ber list.

Delete the relevant call
number (MSN) from the
list (page 24).

No call charges

are dis-

played.

Call charge display has
not been activated or this
feature has not been en-
abled by your provider.

Activate call charge dis-
play (page 67).

Apply to your provider to
enable the “Charge
transmission” feature.

For PABXs:

There is no connection or
a wrong connection after
dialling a call number.

The access code has not
be entered or has been
entered incorrectly.

Check and correct the
access code (page 82).

Question

Possible cause

Possible solution

Summary of Contents for Gigaset 4000 Comfort





















































































































Search results

Summary of Contents for Gigaset 4000 Comfort

Reviews:

Related manuals for Gigaset 4000 Comfort

Brands by name

Popular brands

Siemens Gigaset 4000 Comfort, Operating Instructions Manual

Search results

Summary of Contents for Gigaset 4000 Comfort

Reviews:

Related manuals for Gigaset 4000 Comfort

Brands by name

Popular brands