Siemens Gigaset 4000 Comfort Operating Instructions Manual Download Page 14

Page: 14 / 116

Putting the telephone into operation

Gigaset 4110isdn, GBR, A31008-G4110-B102-2-7619

Inbetriebnahme.fm

4.9.02

Step

step

Connecting the base

●

Only use the plug-in power supply unit provided

(as identified on the

underside of the base).

Plug-in power sup-
ply unit
(220/230 V with
mains cable)

●

Plug the

small

mains cable
connector

into

the socket,

●

Place the cable
in the cable
channel,

●

Connect the

plug-in power
supply unit to
the socket.

●

Plug the

phone cable’s connector

into the socket (latches into position),

●

Place the cable in the cable channel,

●

Plug the phone connector into the
phone socket/NTBA.

Phone connector with phone cable

Key for
registering other
handsets
(see page 18)

Info

Only use the cable provided.

Summary of Contents for Gigaset 4000 Comfort





















































































































Search results

Summary of Contents for Gigaset 4000 Comfort

Reviews:

Related manuals for Gigaset 4000 Comfort

Brands by name

Popular brands

Siemens Gigaset 4000 Comfort, Operating Instructions Manual

Search results

Summary of Contents for Gigaset 4000 Comfort

Reviews:

Related manuals for Gigaset 4000 Comfort

Brands by name

Popular brands