Siemens Gigaset 4000 Comfort Operating Instructions Manual Download Page 90

Page: 90 / 116

Appendix

Gigaset 4110isdn, GBR, A31008-G4110-B102-2-7619

Anhang.fm

4.9.02

The handset

does not

ring as it was set to.

Other ringer melody set-
ting for MSN.

Change the ringer melo-
dy setting (page 33).

Some of the

ISDN func-

tions

do not work as

indicated.

Feature not enabled?

Contact your provider for
information.

Another

phone

on the

So bus

does not ring

The same MSN number
was assigned for the
phones.

Internal

for-

warding has additionally
been activated for one of
the phones.

Deactivate internal for-
warding or set external
call forwarding (page 55).

Caller receives ringing
despite MSN being busy.

MSN has been stored in
devices additionally op-
erated on the ISDN line.

Where applicable, delete
the call number for which
do-not-disturb is to apply
while a call is in progress
from the list of call num-
bers of each additional
device.

Handset does not re-
ceive SMS as text

You are not registered
with both SMS centres

Question

Possible cause

Possible solution

Summary of Contents for Gigaset 4000 Comfort





















































































































Search results

Summary of Contents for Gigaset 4000 Comfort

Reviews:

Related manuals for Gigaset 4000 Comfort

Brands by name

Popular brands

Siemens Gigaset 4000 Comfort, Operating Instructions Manual

Search results

Summary of Contents for Gigaset 4000 Comfort

Reviews:

Related manuals for Gigaset 4000 Comfort

Brands by name

Popular brands