Siemens Gigaset 4000 Comfort Operating Instructions Manual Download Page 76

Page: 76 / 116

Short messages (SMS)

Gigaset 4110isdn, GBR, A31008-G4110-B102-2-7619

sms.fm

4.9.02

Step

step

Display or dial the call number from the SMS message or save it to the
directory

Press

for selection menus.

Select using [OK]:

Text Message

Select using [

] and [OK]:

Incoming

Select using [

] and [

(required SMS)

Display receive MSN (who is the SMS message for?)

Select using [

] and [OK]:

Display entry

The receive MSN will be displayed.

Display the call number of the sender of the SMS message (who is the
SMS message from?)

Select using [

] and [OK]:

Display entry

. The call number will be displayed.

Dial the call number of the SMS message

Select using [

] and [OK]:

Dial number

Store the call number of the SMS message in the directory

Select using [

] and [OK]:

Copy to dir.

Summary of Contents for Gigaset 4000 Comfort





















































































































Search results

Summary of Contents for Gigaset 4000 Comfort

Reviews:

Related manuals for Gigaset 4000 Comfort

Brands by name

Popular brands

Siemens Gigaset 4000 Comfort, Operating Instructions Manual

Search results

Summary of Contents for Gigaset 4000 Comfort

Reviews:

Related manuals for Gigaset 4000 Comfort

Brands by name

Popular brands