Siemens Gigaset 4000 Comfort Operating Instructions Manual Download Page 95

Page: 95 / 116

Appendix

Gigaset 4110isdn, GBR, A31008-G4110-B102-2-7619

Anhang.fm

4.9.02

Technical data

Recommended batteries:

Handset operating/charging times:

We recommend allowing the full, uninterrupted charging time (see table) when
charging for the first time – regardless of what the charging status display
shows.

The batteries’ charge capacity will be less after a few years. This is for technical
reasons.

Power consumption:

– In standby state (without charging), approx. 2.6 watt.
– In standby state while charging, approx. 5.7 watt.

– In the talk state (without charging), approx. 3.0 watt.

Nickel-Cadmium (NiCd)

Nickel-Metal Hydride (NiMH)

Sanyo N-3U
(700 mAh)

Saft RH 6 NiMH 1300
(1300 mAh)

Mobile Power 700
(700 mAh)

Panasonic HHR-110 AA
(1100 mAh)

Panasonic 600 DT
(600 mAh)

Sanyo HR-3U
(1600 mAh)

Emmerich 700
(700 mAh)

GP GP130 AAHC
(1300 mAh)

Varta Phone Power
(1300 mAh)

Emmerich 1300
(1300 mAh)

Capacity
(mAh)

Operating time
(hours)

Talk time
(hours)

Charging time
(hours)

700

up to 180

over 10

about 5.5

1200

up to 300

over 17

about 11

1600

up to 400

over 23

about 14

Info

Summary of Contents for Gigaset 4000 Comfort





















































































































Search results

Summary of Contents for Gigaset 4000 Comfort

Reviews:

Related manuals for Gigaset 4000 Comfort

Brands by name

Popular brands

Siemens Gigaset 4000 Comfort, Operating Instructions Manual

Search results

Summary of Contents for Gigaset 4000 Comfort

Reviews:

Related manuals for Gigaset 4000 Comfort

Brands by name

Popular brands