Siemens Gigaset 4000 Comfort Operating Instructions Manual Download Page 86

Page: 86 / 116

Operation using a telephone system

Gigaset 4110isdn, GBR, A31008-G4110-B102-2-7619

Wahloptionen.fm

4.9.02

Step

step

4th step

Now additionally assign the Gigaset terminals (e.g. “Internal 0” and
“Internal 1”) the previously stored fourth MSN as the

receive

MSN.

is pressed for menus.

Press [

] and [OK ] to select:

Base Settings

→

Settings

→

System settings

→

Setup user

→

Setup device

→

Press [

] to open the additional menu

→

Re-

ceive MSN

5th step

Now store this

Receive MSN

in your ISDN PBX as the internal MSN. Calls for

this internal MSN will then be signalled simultaneously for example at
“Internal 0” or “Internal 1”

. Proceed as described in steps 3 to 5 to form addi-

tional call groups.

Summary of Contents for Gigaset 4000 Comfort





















































































































Search results

Summary of Contents for Gigaset 4000 Comfort

Reviews:

Related manuals for Gigaset 4000 Comfort

Brands by name

Popular brands

Siemens Gigaset 4000 Comfort, Operating Instructions Manual

Search results

Summary of Contents for Gigaset 4000 Comfort

Reviews:

Related manuals for Gigaset 4000 Comfort

Brands by name

Popular brands