SICK HIPERFACE DSL Technical Information Download Page 35 | Manualshive

Page: 35 / 172

SICK HIPERFACE DSL Technical Information Download Page 35

Bit 7

Bit 0

Bit 7-0

ES

: External synchronization

00000000 = Position sampling during free running at the shortest cycle time.

All other values = Position sampling with the

sync

signal synchronized. The value from

ES

determines the number of position samplings carried out in one

sync

cycle. The

user must match the number of samplings per cycle to the shortest frame length (see

6.3.3

Quality monitoring

The

MASTER_QM

quality monitoring register contains the quality monitoring value for

the data connection.

As soon as the DSL Master detects events that indicate an improvement or degrad-
ation of the quality of the data connection, these events are indicated as values higher
or lower than the quality monitoring value (see

).

Table 21: Quality monitoring events

Protocol event

Value change in quality moni‐
toring

Wrong synchronization in Safe Channel (last byte)

-4

Wrong synchronization in Safe Channel (1

st

… 7

th

bytes)

-6

RSSI <2

-4

Wrong encoding in parameter or SensorHub channels

-1

Wrong encoding in process data channel

-2

Unknown special characters in the protocol package

-2

Any identified error in Safe Channel 1

-6

Any identified error in Safe Channel 2

-8

Correct synchronization in Safe Channel

+1

Correct CRC value in Safe Channel

+1

Quality monitoring is initiated with the value "8".

The maximum quality monitoring value is "15". This is the standard value during opera‐
tion.

NOTE

Particular attention must be paid to the quality monitoring value during the develop‐
ment of a DSL drive controller. If a value lower than "15" is indicated, the cause may be
a problem with the connection circuit, particularly if the value is continuously displayed.

If the quality monitoring value falls below "14",

QMLW

information is indicated in Online

Status and in the

EVENT_L

register.

If the quality monitoring value falls to "0", a forced reset of the protocol is carried out.
This is indicated by the

PRST

error bit in Online Status and in the

EVENT_H

register.

The

MASTER_QM

register is write protected.

Register 03h:

Quality monitoring register

R-0

X-0

X-0

X-0

R-0

R-0

R-0

R-0

LINK

QM

Bit 7

Bit 0

REGISTER MAP

6

8017595/ZTW6/2018-01-15 | SICK

T E C H N I C A L I N F O R M A T I O N | HIPERFACE DSL

®

35

Subject to change without notice

«
...
33
34
35
36
37
...
»

Summary of Contents for HIPERFACE DSL













































































































































































Reviews:

No comments