UP-5900VS
DIAGNOSTICS SPECIFICATIONS
4 – 13
2
Display
Select the desired items at the position of @. (@ is not displayed on
the screen.)
(On the above screen, the thick figures are selected, and the thick
figure values are selected.)
On the above screen, when the pass count is counted up (when
point is counted up to the upper limit set in the cylinder range set-
ting, the pass count is counted up by 1.), and if the error counter of
all error items are not counted up (remaining as 00000), the test is
OK.
3
Terminating method
The methods to interrupt, resume, and terminate the test are same
as (2) Sequential read.
6) HD DUMP TEST
[Test conditions setting]
• Cylinder No. [0 ~ inmost cylinder]
A certain cylinder No. to be displayed is set.
• Head No. [0 ~ final head]
A certain head No. to be displayed is set.
• Sector No. [1 ~ final sector]
A certain sector No. to be displayed is set.
1
Checking content
The sector set in the above is displayed on the screen in the unit of
256byte.
Hex data and ASCII characters are displayed.
By key operation, the following 256 bytes data or previous 256 bytes
data can be displayed.
2
Display
The physical address is set at the position of @. (On the above
screen, the thick value is set.)
On the above screen, the first-half of 256 bytes at 000 cylinder, 00
head, and 01 sector is displayed.
Press the page down key to display the second-half of 256 bytes.
(When the page down key is pressed on the above screen, the sec-
ond-half of 256 bytes at 000 cylinder, 00 head, and 01 sector is dis-
played.)
Press the page up key to display the first-half of 256 bytes.
3
Terminating method
Press the Esc key to return to the menu screen of previous (1).
7) ERROR INFORMATION DISPLAY
1
Checking content
Error information stored in the inmost area of the HDD is displayed.
When the hard disk test is executed, error information stored in the
error information storing area is displayed.
The inmost cylinder, 0 head, and 1 sector ~ 6 sector are read to be
displayed.
2
Display
Every time the Enter key is pressed, the next page error information
is displayed.
[Descriptions on the above screen]
3
Terminating method
Press the Esc key to return to the menu screen.
Target Sector Read test
@Cylinder range ?
[000 XXX] = 000-XXX
(XXX is displayed by checking the
inmost cylinder.)
@Head count ?
[0 XX] = 0
(XX is displayed by checking the
final head.)
@Sector count ?
[0 XX] = XX
(XX 8s displayed by checking the
max. sector.)
@Retry count ?
[0 4] = 0
@[Errorstop continue 1pass]
@Test Start ? [Yes No]
Pass count = XXXXX
Test Point = CCC : HH : SS (Cylinder: head; sector)
Error Kinds
Drive not ready XXXX
Bad controller XXXX
Compare error XXXX
ESC : Exit SPACE : Stop or Start
Details of error are displayed.
Error No. _________
Error information register No. (001 ~)
(This is not an error code.)
YY/MM/DD________
Year/Month/Day
HH:MM:SS _______
Hour/Minute/Second
Cylinder __________
Cylinder No.
Head No. _________
Head No.
Sec No. __________
Sector No.
Error Content _____
Error code is converted into error content
and displayed.
HD Dump test
@Physical address ? [CCC. HH. SS] = 000. 00. 01
The first hslf sector
000 : HHHH......HHHH-HHHH......HHHH : AAA......AA
(100)
PGDN : forward PGUP : back SPACE : Start ESC : Exit
:
010 : HHHH......HHHH-HHHH......HHHH : AAA......AA
(110)
:
0F0 : HHHH......HHHH-HHHH......HHHH : AAA......AA
(1F0)
:
020 : HHHH......HHHH-HHHH......HHHH : AAA......AA
(120)
:
:
Error Logging information Display
Error
No.
001
002
003
004
005
006
007
ESC : Exit ENTER : Next
YY/MM/DD
99 / 03 / 01
HH : MM : SS
10 : 30 : 00
Cyl
No.
100
Hed
No.
03
Sec
No.
01
Error
Content
XXXXXXX
