SEW-Eurodrive MOVIMOT MMxD Series Compact Operating Instructions Download Page 17

Page: 17 / 68

Mechanical installation

Mounting MOVIMOT® inverter close to the motor

Compact Operating Instructions – MOVIMOT

MM..D with AS-Interface

4.4.3

Installation in damp locations or in the open

Observe the following notes for mounting the MOVIMOT

drive in damp areas or in

the open:

• Use suitable cable glands for the incoming cables. Use reducing adapters if neces-

sary.

• Coat the threads of the cable glands and screw plugs with sealing compound and

tighten them properly. Then coat the cable glands again.

• Seal the cable entry properly.

• Thoroughly clean the sealing surfaces of the MOVIMOT

inverter before re-assem-

bly.

• If the corrosion protection coating is damaged, restore the coating.
• Check whether the degree of protection specified on the nameplate is permitted in

the ambient conditions on site.

4.5

Mounting MOVIMOT

inverter close to the motor

Mounting

MOVIMOT®

inverter

close to the

motor

The following figure shows the mounting dimensions for mounting the MOVIMOT

in-

verter close to the motor:

9007199713018763

Size

Type

MM03D503-00 – MM15D-503-00
MM03D233-00 – MM07D-233-00

140 mm

65 mm

2/2L

MM22D503-00 – MM40D-503-00
MM11D233-00 – MM22D-233-00

170 mm

65 mm

21328994/EN – 11/2014

Summary of Contents for MOVIMOT MMxD Series





































































Search results

Summary of Contents for MOVIMOT MMxD Series

Reviews:

Related manuals for MOVIMOT MMxD Series

Brands by name

Popular brands

SEW-Eurodrive MOVIMOT MMxD Series, Compact Operating Instructions

Search results

Summary of Contents for MOVIMOT MMxD Series

Reviews:

Related manuals for MOVIMOT MMxD Series

Brands by name

Popular brands