Server Technology Switched Rack PDU Page 25 Installation And Operation Manual Download

Page: 25 / 157

Switched PDU
Installation and Operations Manual

Operations



High Limit:

Displays the high limit of the load, temperature, or humidity graph. These values depend on the sensor

limits are cannot be set by the user. For example, a 100ºC high limit would be displayed as

for a temperature

sensor graph in Celsius.

Status:

One of several operating conditions:

System Summary

– Status Descriptions

Icon

Status

Description

Reading

Unit is reading a new or restored sensor.

Normal

Indicates normal operation.

Load High

Infeed current load exceeds present High threshold.

Over Load

Infeed current load exceeds the measurable range for the infeed.

Temp Low

Current temperature falls below present Low threshold.

Temp High

Current temperature exceeds present High threshold.

Humid Low

Current percentage of relative humidity falls below present Low threshold.

Humid High

Current percentage of relative humidity exceeds present High threshold.

Lost

The connection was lost to a sensor that was previously detected and the sensor is pulled from the

original environment monitoring statistics. There is no data to report, the graph is meaningless, and

the threshold settings remain displayed but are grayed.

Sensor Graph Color-Coding

The following colors change dynamically on the sensor graphs to communicate operating conditions:

Line (Load) Status:

Green = Normal

Yellow = High load (load configured by user)

Red = Overload (based on device characteristics)

User configures load capacity at

Configuration > SNMP/Thresholds > Input Feed Traps and Thresholds

Temperature Status:

Blue = cold; low temperature (threshold configured by user)

Green = acceptable temperature range

Red = hot; high temperature (threshold configured by user)

User configures low/high temperature thresholds at

Configuration > SNMP/Thresholds > Sensor Traps and

Thresholds

Humidity Status:

Blue = wet; high humidity (threshold configured by user)

Green = acceptable percentage of relative humidity

Yellow = dry; low humidity (threshold configured by user)

User configures low/high relative humidity thresholds at

Configuration > SNMP/Thresholds > Sensor Traps and

Thresholds

Summary of Contents for Switched Rack PDU






























































































































































Search results

Summary of Contents for Switched Rack PDU

Reviews:

Related manuals for Switched Rack PDU

Brands by name

Popular brands

Server Technology Switched Rack PDU, Installation And Operation Manual

Search results

Summary of Contents for Switched Rack PDU

Reviews:

Related manuals for Switched Rack PDU

Brands by name

Popular brands