Server Technology Switched Rack PDU Installation And Operation Manual Download Page 134 | Manualshive

Page: 134 / 157

background image

134



Advanced Operations

Switched PDU

Installation and Operations Manual

Setting the number of RADIUS server retries:

The Set RADIUS Retries command specifies the number of times an authentication request is sent to the RADIUS
server. The PDU will attempt authentication with the primary server until the number of retries is reached, then will
attempt authentication with the secondary server. If the PDU does not receive a response from these attempts, the
authentication request will be rejected.

To set the number of retries:

At the Switched CDU: prompt, type

set radius

, followed by

primary

or

secondary

, followed by

retries

, followed by

the number of retries, and press

Enter

.

The valid retries range is 0-10; default is 2.

Examples

The following command sets the retries for the primary RADIUS server to 5:

Switched CDU: set radius primary retries 5<Enter>

The following command sets the retries for the secondary RADIUS server to 2:

Switched CDU: set radius secondary retries 2<Enter>

Displaying RADIUS configuration information:

The Show RADIUS command displays RADIUS configuration information.

To display the RADIUS configuration information:

At the Switched CDU: prompt, type

show radius

and press

Enter

.

Example

The following command displays the RADIUS configuration information:

Switched CDU: show radius<Enter>
RADIUS Configuration

RADIUS:

Enabled

Auth Order: Remote->Local
Primary Server:

Shared Secret: ****

Port: 1812
Timeout: 15 seconds
Retries: 5

Secondary Server:

Shared Secret:

Port: 1855
Timeout: 5 seconds
Retries: 2

«
...
132
133
134
135
136
...
»

Summary of Contents for Switched Rack PDU






























































































































































Reviews:

No comments

Related manuals for Switched Rack PDU

Brand: Baumuller Pages: 72

Brand: Vertiv Pages: 29

Brand: IB Connect Pages: 12

Brand: Nordost Pages: 5

Brand: Panamax Pages: 17

Brand: Unika Pages: 4

SmartOnline B020-016 6

Brand: Tripp Lite Pages: 2

Brand: Tripp Lite Pages: 2

Brand: Tripp Lite Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands