Server Technology Switched Rack PDU Installation And Operation Manual Download Page 153 | Manualshive

Page: 153 / 157

background image

Switched PDU
Installation and Operations Manual

Appendices



153

RJ45 to DB9F serial port adapter

Additionally, an RJ45 to DB9F serial port adapter is provided for use in conjunction with the RJ45 crossover cable to
connect to a PC DB9M DCE serial port. The adapter pinouts below reflect use of the adapter with the provided RJ45
crossover cable.

Pin

DCE Signal Name

Input/Output

1

2

Receive Data

RD

Output

3

Transmit Data

TD

Input

4

Data Terminal Ready DTR

Input

5

Signal Ground

6

Data Set Ready

DSR

Output

7

Request to Send

RTS

Input

8

Clear to Send

CTS

Output

LED Indicators

Input/Branch/Phase Current

Units are equipped with 7-segment LEDs for reporting of input, branch, or phase current loading. Loading is reported
in amperes and is displayed in

1

/

8

, ½, or 0.1 amp increments under 10A and whole amp increments at and above 10A.

Additionally, the LED can display codes for events detected by the system for immediate local notification.

Behavior/Code

Event description

Blinking

The unit blinks half-second on, half-second off when the current exceeds the user-

defined “high load” or

factory default threshold (80% of maximum Input Feed Capacity).

“oL”

Flashes “oL” when the current exceeds the Input Feed Capacity.

FE

The PDU has detected an error with the Branch Circuit Protection. For units with a fuse, check to see if the
fuse was blown or removed; for units with a circuit breaker, check to see if the breaker was tripped.

Outlets

Units are equipped with a status LED for each power receptacle. A lit (on) LED indicates that power is being supplied
at the port and a dim (off) LED indicates that there is no power at the port.

1

2

3

4

5

6

7

8

9

«
...
151
152
153
154
155
...
»

Summary of Contents for Switched Rack PDU






























































































































































Reviews:

No comments

Related manuals for Switched Rack PDU

Brand: Samson Pages: 2

Brand: Ultra Pages: 5

Brand: ABB Pages: 1016

Brand: Dawnco Pages: 16

Brand: Compaq Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands