Server Technology Switched Rack PDU Page 84 Installation And Operation Manual Download | Manualshive

Page: 84 / 157

background image

84



Operations Switched PDU

Installation and Operations Manual

Setting the IP address:

The Set Ipaddress command sets the TCP/IP address of the network interface controller.

To set the IP address:

At the Switched CDU: prompt, type

set ipaddress

, followed by the IP address and press

Enter

.

NOTE:

Both IPv4 and IPv6 IP address formats are accepted.

Example

The following command sets the IP address to 12.34.56.78:

Switched CDU: set ipaddress 12.34.56.78<Enter>

Setting the subnet mask:

The Set Subnet command sets the subnet mask for the network the PT40 will be attached to.

To set the subnet mask:

At the Switched CDU: prompt, type

set subnet

, followed by the subnet mask and press

Enter

.

Example

The following command sets the subnet mask to 255.0.0.0

Switched CDU: set subnet 255.0.0.0<Enter>

Setting the gateway:

The Set Gateway command sets the IP address of the default gateway the PDU uses to access external networks.

To set the gateway IP address:

At the Switched CDU: prompt, type

set gateway

, followed by the gateway IP address and press

Enter

.

Example

The following command set the gateway IP address to 12.34.56.1:

Switched CDU: set gateway 12.34.56.1<Enter>

Setting the DNS IP address:

The Set DNS command sets the TCP/IP address of the Domain Name server (DNS).

To set the DNS IP address:

At the Switched CDU: prompt, type

set

, followed by

dns1

or

dns2

and the Domain Name server’s IP address. Press

Enter

.

NOTE:

Both IPv4 and IPv6 formats are accepted for DNS IP address.

Example

The following command sets the primary Domain Name server IP address to 98.76.54.254:

Switched CDU: set dns1 98.76.54.254<Enter>

Displaying network configuration information:

The Show Network command displays TCP/IP, Telnet, SSH, Web, SSL, SNMP, and DHCP options (when DHCP is
enabled) configuration information. The Show Network command also displays all IPv4 and IPv6 settings.



Network configuration: IP address, subnet mask, gateway and DNS IP addresses (both IPv4 and IPv6
formats are displayed). (both IPv4 and IPv6 formats are displayed).



Enabled-disabled status and port numbers for Telnet, SSH, HTTP, SSL, SNMP, and FTP Server support.



Network status: Link, speed, duplex, and negotiation.



DHCP boot delay and DHCP static address fallback options (when DHCP is enabled).



Enabled-disabled status of Sentry Power Manager (SPM).

«
...
82
83
84
85
86
...
»

Summary of Contents for Switched Rack PDU






























































































































































Reviews:

No comments

Related manuals for Switched Rack PDU

Brand: PowerWalker Pages: 12

Brand: Furman Pages: 28

Brand: Vertiv Pages: 16

Brand: Pentair Pages: 2

Brand: Arconic Pages: 16

Brand: Panamax Pages: 16

Brand: NF Pages: 290

Brand: P.Lindberg Pages: 38

PowerWorx Select Series

Brand: ADC Pages: 32

PowerWorx Power Distribution Products

Brand: ADC Pages: 40

Brand: Good Will Instrument Pages: 249

Brand: Tripp Lite Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands