manualshive.com logo in svg

Server Technology Switched Rack PDU, Installation And Operation Manual, Page: 148 / 157

Share
Download
Server Technology Switched Rack PDU Installation And Operation Manual Download Page 148

148

 

 Appendices   

     Switched PDU 

  

 

Installation and Operations Manual 

Appendix B: Uploading Firmware 

You can upload new versions of firmware using File Transfer Protocol (FTP). This allows access to new firmware 
releases for firmware improvements and new features additions.   

NOTE:

 To begin an FTP upload session, you must first configure the FTP Host address, username/password, filename, and filepath. 

You can initiate an FTP upload session by issuing a command or from the Web interface.  Upon initiating an FTP 
upload session, the unit will restart and upload the firmware file specified with the FTP Filename command from the 
previously configured FTP Host. You must have administrator-level privileges to initiate an upload.   

Initiate an FTP upload session from the Web interface 

On the Restart page in the Tools section of the Web interface, select 

Restart and upload firmware via FTP 

from the 

drop-down menu and click 

Apply

. 

Initiate an FTP upload session from the command line 

To initiate an FTP firmware upload session:  

At the Switched CDU: prompt, type 

restart ftpload

 and press 

Enter

. 

Summary of Contents for Switched Rack PDU






























































































































































Reviews:

No comments