Server Technology Switched Rack PDU Page 77 Installation And Operation Manual Download | Manualshive

Page: 77 / 157

background image

Switched PDU
Installation and Operations Manual

Operations



77

Displaying system configuration information:

The Show System command displays all system configuration information.



Firmware version



NIC module serial number and MAC address



Hardware revision code and Flash size



Uptime since last system restart



System location description



Area (footprint) and power factor



3-phase load out-of-balance threshold and alert status

To display system configuration information:

At the Switched CDU: prompt, type

show system

and press

Enter

.

Example

System Information
  F/W Version: Sentry Version 6.0a
  NIC S/N: 1600001
  MAC Address: 00-0a-9c-10-00-01
  H/W Rev Code: 0
  Flash Size:     2 MB
  Uptime: 0 days 6 hours 14 minutes 1 second
  Location: Florida HQ
  Area <Footprint>: 6.3 square feet
  Power Factor: 0.80
  3-Phase Load Out-of-Balance
  Threshold: 20 percent
  Alerting: Enabled

Displaying system power status:

The System Status command displays system power and tower information.

To display system power status:

At the Switched CDU: prompt, type

sysstat

and press

Enter

.

Example

Switched CDU: sysstat
System Power Status
Total Power Consumption: 170 Watts
Area <Footprint>: 100.0 Square Meters
Watts Per Area Unit: 2 Watts Per Square Meter
Tower Status
Tower Tower Tower
ID Name Status

.A TowerA Normal
.B TowerB Normal

Command successful

NOTE:

For 3-phase systems, if the Out-of-Balance Alerting feature is enabled, and the system goes into a load out-of-balance condition,

the System Status command will display the alert “3ph Out-of-Balance” in the Tower Status section, unless there is a higher priority tower
error state to report.

«
...
75
76
77
78
79
...
»

Summary of Contents for Switched Rack PDU






























































































































































Reviews:

No comments

Related manuals for Switched Rack PDU

Brand: LEGRAND Pages: 5

Brand: ICM Controls Pages: 2

Brand: GW Instek Pages: 265

Brand: D&R ELECTRONICS Pages: 12

Brand: D&R ELECTRONICS Pages: 16

Brand: QNect Pages: 2

Brand: Bachmann Pages: 20

Brand: Delta Pages: 3

Enlogic EN2.0 Series

Brand: CIS Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands