manualshive.com logo in svg

SELVA MARINE Kingfish 25, Service Manual

The SELVA MARINE Kingfish 25 is a powerful and reliable outboard motor perfect for all your boating needs. For detailed maintenance and repair instructions, download the free Service Manual from manualshive.com. Keep your engine running smoothly with this essential manual at your fingertips.

Share
Download
background image

8-52

8

Shimming (high thrust model)

Shimming workflow

TIP:

• Shimming is not required if the backlash is within specification.
• Shimming is required when assembling the original inner parts and a new lower case.
• Shimming is required when replacing the pinion, forward gear, reverse gear, bearings, shaft, or

propeller shaft housing.

NO

YES

Shimming is not required.

YES

NO

Within specification?

Disassemble the lower unit.

Select the pinion shims (T3).

Assemble the lower unit.

Measure the backlash.

Adjust the forward gear shim 
thickness (T1) and reverse gear 
shim thickness (T2).

Install the water pump assem-
bly.

Within specification?

Remove the water pump 
assembly.

Measure the backlash before 
disassembly.

Drive shaft and lower case (high thrust model) / Shimming (high thrust model)

Summary of Contents for Kingfish 25















































































































































































































































































































































































































Reviews:

No comments

Related manuals for Kingfish 25

Panasonic PAN9420 Quick Start Manual preview
PAN9420
Brand: Panasonic Pages: 26
Texas Instruments INA193EVM User Manual preview
INA193EVM
Brand: Texas Instruments Pages: 8
MPS EV6001DN-00D Quick Start Manual preview
EV6001DN-00D
Brand: MPS Pages: 6
Gigabyte GA-8VM533 User Manual preview
GA-8VM533
Brand: Gigabyte Pages: 96
Biostar TPower I45 Bios Manual preview
TPower I45
Brand: Biostar Pages: 43
Gigabyte GA-K8NSNXP User Manual preview
GA-K8NSNXP
Brand: Gigabyte Pages: 96
Supermicro H8QG7-LN4F User Manual preview
H8QG7-LN4F
Brand: Supermicro Pages: 84
Supero X9DRT-HF+ User Manual preview
X9DRT-HF+
Brand: Supero Pages: 105
MSI MS-6721 User Manual preview
MS-6721
Brand: MSI Pages: 75
NXP Semiconductors i.MX RT1020 Quick Start Manual preview
i.MX RT1020
Brand: NXP Semiconductors Pages: 4
Gigabyte GA-7VM400M-P User Manual preview
GA-7VM400M-P
Brand: Gigabyte Pages: 96
Fujitsu D1170 Technical Manual preview
D1170
Brand: Fujitsu Pages: 22
Fujitsu D1031 Technical Manual preview
D1031
Brand: Fujitsu Pages: 23
Fujitsu D1483 Tehnical Manual preview
D1483
Brand: Fujitsu Pages: 28
Fujitsu D2239 Technical Manual preview
D2239
Brand: Fujitsu Pages: 39
Fujitsu D1526 Technical Manual preview
D1526
Brand: Fujitsu Pages: 44
Fujitsu CREMSON MODULAR STARTERKIT User Manual preview
CREMSON MODULAR STARTERKIT
Brand: Fujitsu Pages: 36
Fujitsu D1837 Technical Manual preview
D1837
Brand: Fujitsu Pages: 48

Brands by name

Popular brands

Load more brands